Futaba 10CAG Gebrauchsanleitung
49
SUB-TRIM
: makes small changes or corrections to the neutral position of each servo. Range is -120 to +120, with 0 setting,
the default, being no SUB-TRIM.
We recommend that you center the digital trims before making SUB-TRIM
changes, and that you try to keep all of the SUB-TRIM values as small as
possible. Larger SUB-TRIM values affect the servo's range of travel is restricted
on one side.
changes, and that you try to keep all of the SUB-TRIM values as small as
possible. Larger SUB-TRIM values affect the servo's range of travel is restricted
on one side.
The recommended procedure is as follows:
• measure and record the desired surface position;
• zero out both the trims (TRIM RESET menu) and the SUB-TRIMs (this menu);
• mount servo arms and linkages so that the control surface’s neutral is as correct as possible; and
• use a small amount of SUB-TRIM
• measure and record the desired surface position;
• zero out both the trims (TRIM RESET menu) and the SUB-TRIMs (this menu);
• mount servo arms and linkages so that the control surface’s neutral is as correct as possible; and
• use a small amount of SUB-TRIM
WRPDNH¿QHFRUUHFWLRQV
GOAL of EXAMPLE:
STEPS:
INPUTS:
Adjust the flap servo's SUB-TRIM until
its center exactly matches the aileron
servo's center, as they work together as
ÀDSHURQV
its center exactly matches the aileron
servo's center, as they work together as
ÀDSHURQV
Open BASIC menu, then open SUB-TRIM.
for 1 second.
(If ADVANCE,
again.)
C
to SUB-TRIM.
Choose the channel to adjust, and adjust
XQWLOVXUIDFHVPDWFK ([ ÀDS
XQWLOVXUIDFHVPDWFK ([ ÀDS
C
to FLAP
as needed.
C
to each channel,
Repeat for other channels.
as needed.
Close.
Where next?
Adjust trim steps: see p. 48.
Adjust END POINTs: see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO D/R,EXP): see p. 42.
Adjust END POINTs: see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO D/R,EXP): see p. 42.
The servo submenu includes two features:
• real-time bar-graph display to demonstrate exactly what commands the
• real-time bar-graph display to demonstrate exactly what commands the
transmitter is sending to the servos. (This can be particularly handy in setting
up models with complicated mixing functions, because the results of each
stick, lever, knob, switch input and delay circuit may be immediately seen.)
up models with complicated mixing functions, because the results of each
stick, lever, knob, switch input and delay circuit may be immediately seen.)
VHUYR F\FOH IXQFWLRQ WR KHOS ORFDWH VHUYR SUREOHPV SULRU WR LQÀLJKW IDLOXUHV
(channels 1-8)
GOAL of EXAMPLE:
STEPS:
INPUTS:
View the result of reassigning channel
6 from VR(A) knob to three-position
SWITCH C.
6 from VR(A) knob to three-position
SWITCH C.
Cycle the channel 6 servo.
C o m p l e t e d e s i r e d p r o g r a m m i n g
function. (Ex: in AUX-CH, move ch. 6 to
SWITCH C)
function. (Ex: in AUX-CH, move ch. 6 to
SWITCH C)
See AUX-CH for details. (p. 39.)
Open the SERVO function.
for 1 second.
(If ADVANCE,
again.)
C
to SERVO.
Move each control to see the operation.
(Ex: SWITCH C in all positions)
(Ex: SWITCH C in all positions)
C to center position.
Note change in position of ch. 6 servo.
Prepare all servos to be cycled and cycle. Plug in servos. POWER ON.
End cycling and close.
Where next?
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO D/R,EXP): see p. 42.
Set up desired programmable mixes: see p. 61.
Set up dual aileron servos: see p. 51.
Set up dual elevator servos: see p. 57.
Set up desired programmable mixes: see p. 61.
Set up dual aileron servos: see p. 51.
Set up dual elevator servos: see p. 57.
SERVO
display and cycle submenu: displays radio's output to channels 1-10.