Fusionbrands Fusionbrands, Inc. Marine Radio MS-NRX200 Benutzerhandbuch
(b) New NMEA2000 Network
Fusion provides a NMEA2000 Starter Kit MS-N2KSTART for creating a new NMEA2000 network on
your vessel.
Fusion provides a NMEA2000 Starter Kit MS-N2KSTART for creating a new NMEA2000 network on
your vessel.
MS-N2KSTART - NMEA2000 Starter Pack
3 x NMEA2000 T-Connectors
1 x Terminator Micro C - Male
1 x Terminator Micro C - Female
1 x NMEA2000 Power Cable
2 x Drop Cable, FUSION to NMEA2000 Micro-C
1 x 6M Backbone Cable, Micro C Male - Female
3 x NMEA2000 T-Connectors
1 x Terminator Micro C - Male
1 x Terminator Micro C - Female
1 x NMEA2000 Power Cable
2 x Drop Cable, FUSION to NMEA2000 Micro-C
1 x 6M Backbone Cable, Micro C Male - Female
Note: The supplied Terminator must be fitted to the ends of the network as shown. Failure to do so will
effect operation.
effect operation.
Optional Accessory:
MS-N2KEXT6 - 6m extension lead
MS-N2KEXT20 - 20m extension lead
6
POWER ON/OFF – NMEA2000 REPEATER MODE
If the remote control has been configured to display NMEA2000 data sentences it can be turned on
independently of the FUSION Marine Stereo. This permits the user to monitor NMEA data without turn-
ing on the stereo.
independently of the FUSION Marine Stereo. This permits the user to monitor NMEA data without turn-
ing on the stereo.
Press
to turn on the remote control. The remote control will enter NMEA2000 repeater mode and
will NOT turn on the stereo. The stereo can be turned on from the remote control by pressing the Menu
key to exit the NMEA2000 repeater mode. To return to the repeater mode press and hold the Source
key.
key to exit the NMEA2000 repeater mode. To return to the repeater mode press and hold the Source
key.
When in NMEA2000 repeater mode the remote will monitor the state of the stereo. If the stereo is
turned on then the remote will allow the user to change volume and mute the stereo, play, pause and
skip track (back and forwards) without leaving NMEA2000 repeater mode.
turned on then the remote will allow the user to change volume and mute the stereo, play, pause and
skip track (back and forwards) without leaving NMEA2000 repeater mode.
TURNING ON THE REMOTE CONTROL WITH THE MARINE STEREO TURNED ON
Press to turn ON the remote control. It will detect the stereo is on and enter the remote control
mode.
mode.
CHANGING REMOTE CONTROL MODE
10
The NRX200 remote control can be configured to display NMEA2000 network data, the following
options are available:
options are available:
•
Wind Direction
•
Wind Speed
•
Depth
•
Speed over Ground
•
Speed through Water
•
Heading
•
Position
•
Water Temperature
•
Atmospheric Pressure
•
ETA
SELECTING THE DISPLAY METHOD
The remote control can be configured to automatically cycle through the selected NMEA2000 data.
Press the ‘Menu’ button and select ‘SETTINGS’ > ‘NMEA Monitor’ > ‘CYCLE SCREENS’. Select from the
following options. Press the ‘Menu’ button to exit.
Press the ‘Menu’ button and select ‘SETTINGS’ > ‘NMEA Monitor’ > ‘CYCLE SCREENS’. Select from the
following options. Press the ‘Menu’ button to exit.
•
Off
•
2 seconds
•
5 seconds
•
10 seconds
SELECTING UNITS OF MEASURE
Press the ‘Menu’ button and select ‘SETTINGS’ > ‘NMEA Monitor’ > ‘SET UNITS’. Select from the following
options. Press the ‘Menu’ button to exit.
Distance: KM, Miles, Nautical Miles, Metres, Feet
Speed: KM/H, MPH, KTS, M/S
Depth: Metres, Feet, Fathoms
Temperature; °C, °F
options. Press the ‘Menu’ button to exit.
Distance: KM, Miles, Nautical Miles, Metres, Feet
Speed: KM/H, MPH, KTS, M/S
Depth: Metres, Feet, Fathoms
Temperature; °C, °F
9
MS-NRX200 Manual.indd 7
12/12/2011 3:29:10 p.m.