Fantom Vacuum PT199H Benutzerhandbuch

Ridge for
bag

Attach collector debris bag to Motor when 

you wish to use unit as a vacuum.

Once the tubes and easy grip handle have 

been attached you can proceed to attach 

bag to blower outlet.

1.  Loosen velcro strap on debris collector 

bag. 

2. Place narrow end of adapter into 

debris collector bag. There is enough 

space for collar of bag to sit  above 

ridge created for bag cuff.

3. Pull velcro strap to tighten cuff on 

adapter. Ensure that bag is properly 

attached to avoid debris from being 

thrown out of opening. (Fig. 6)

NOTE: Bag adapter must be in position 

before vacuum tubes can be attached.
5. Angle motor to allow hook on bag 

adapter to securely hook onto last 

bar of easy grip handle. 

6. Lift easy grip handle to secure 

locking tab in place. (Fig. 8)

1. Unplug unit and ensure all parts 

stop moving.

2. Press on locking tab near handle to 

remove easy grip handle from 

motor.  Angle motor to release 

hook from locking bar. (Fig. 9)

Hook bag onto
Last bar of easy grip
handle

Locking tab to 
easy grip handle

Remove the plug 

from the power source before 

assembly of leaf blower. This will help 

prevent accidental starting of the unit 

which could result in serious injury.

4. Align locking tab with motor’s 

locking tab holder and slide onto 

blower outlet until you hear a click . 

(Fig 7)

Attaching Vacuum to Motor

Remove the plug 

from the power source before 

assembly of leaf blower. This will 

help prevent accidental starting of 

the unit which could result in serious 

injury.

The impeller rotates for 

a few seconds after you turn off the 

blower and will cause injury. WAIT until 

all parts stop moving.

Do not remove the 

bottom inlet cover when the motor is 

running or when the unit is plugged into 

power outlet.

Instructions must be followed in 

order.

1.

Ensure unit is unplugged and all 

parts have stopped moving.

2.

Slide blower tube onto the blower 

outlet. (Fig. 1)

Remove the plug from 

the power source before assembly of 

vacuum. This will help prevent accidental 

starting of the unit which could result in 

serious injury.

Do not remove the 

bottom inlet cover when the motor is 

running or when the unit is plugged into 

power outlet

The impeller 

rotates for a few seconds after you 

turn off the blower and will cause injury. 

WAIT until all parts stop moving.
To assemble vacuum tubes instructions 
must be followed in order:

Tab on Tube

1. Align tabs on upper and lower 

vacuum tube ensuring that the guide 
is also aligned.  Forcefully slide  lower 
vacuum tube onto upper vacuum tube 
until upper tube is at end of lower 
tube. Once in place these tubes are 
permanently attached.

4.

Lift handle to lock inlet cover into 

place at rear of  motor. (Fig.3)

IMPORTANT: The blower will not run 

unless the bottom inlet cover is 

locked in place.

NOTE: You must install the blower tube 

before installing the inlet cover because 

the inlet cover hooks onto the blower 

tube.

3.

Attach inlet cover onto hook on 

blower tube. (Fig. 2)

Hook on
blower tube

2. Push easy grip handle into place on 

upper tube. (Fig. 5)

NOTE: This is a permanently assembly, 

there is no reason to take apart 
after assembled.

3. Align notch on easy grip handle with 

tabs on upper tube.

NOTE: The strap on the bag is adjustable 

for comfort of use. It is suggested 

that you place strap across your 

chest. Attach Vacuum to Motor when 

you wish to use unit as a vacuum.

NOTE: Only use vacuum to pick up small 

dry debris such as: grass clippings, 

dry leaves, or small twigs.

DO NOT vacuum up glass, pebbles, 

gravel, or large sticks.

IMPORTANT: The vacuum will not run 

unless the vacuum tube is locked in 

place.

3. Press on locking tab to remove bag 

adapter from unit. (Fig. 10)