Aton AH66T Merkblatt
Start Here
Multi-Source/Multi-Zone Controller
1
3
5
6
7
4
Connect Audio Sources To AH66T – Options
Connect Speakers
Plug in the AH66T to Power Up
Turn On Power to All Connected Sources
Assign Keypads to Their Appropriate Zone.
Connect OLED2 Touchpads
A – Built-in Tuner Setup
B – Sources 1 thru 6 Setup
C – iPod Dock (for MetaData) Setup
D – RadioRA®2 Setup
A – Assign Zone Number
B – Repeat for Zones 2 thru 6
C – Customization
A – Connect RJ-45 Plugs On Both Ends
For audio sources with
an analog audio output,
connect the analog
output to the AH66T
RCA Input with a stereo
RCA cable.
an analog audio output,
connect the analog
output to the AH66T
RCA Input with a stereo
RCA cable.
Once the OLED2's are connected and powered up,
you must assign the keypads to their appropriate
zone.
you must assign the keypads to their appropriate
zone.
Follow the instructions on the OLED2 screen and
assign the zone number to which the keypad is
physically connected
assign the zone number to which the keypad is
physically connected
1. Press UP or DOWN to find the Zone number
to which the keypad is connected.
to which the keypad is connected.
2. Press Enter and then press Enter again.
3. The Zone number should appear on the
upper left corner.
If stacking chassis for a 12 zone configuration, please reference the full installation manual for
connections and considerations.
connections and considerations.
Strip approximately 1/4" of insulation from
both ends of all speaker wiring.
both ends of all speaker wiring.
Twist the exposed end of the wire to ensure no
loose strands remain.
loose strands remain.
Connect the positive speaker wire to the
positive input of the speaker and negative
speaker wire to each negative input of
each speaker.
positive input of the speaker and negative
speaker wire to each negative input of
each speaker.
P/N 9803429 REV A
AH66T
IPort Dock FS-22
RadioRA® 2 Main Repeater
Maximum 50 ft (15 m)
TOTAL wire run.
Stereo RCA
Patch Cable
Patch Cable
Audio Source
Analog Output
Analog Output
FM Antenna
AM Antenna
568A or 568B
(End to end)
DB9M - RJ-45 Adapter
(Included with AH66T)
DB9M - RJ-45 Adapter
(Included with AH66T)
RS-232 Control Cable
(Included with FS-22)
RS-232 Control Cable
Mono 3.5 mm Cable
(Not included)
568A or 568B
(End to end)
Audio Cable
(Included with FS-22)
To IR Emitter
Output
To L/R Audio
Inputs
+12VDC
Power Supply
3.5mm Jack
2
Connect & Mount IR Emitters
Connect the 3.5mm plug of each IR
emitter into the designated port of the
AH66T. The six IR ports labeled 1-6 are
source specific. For example, IR port "1"
must be mounted to the audio source
connected to "source input 1". The "ALL
IR OUT" port is constantly active, and
passes ALL IR 1-6 information, regard-
less of the source selected.
emitter into the designated port of the
AH66T. The six IR ports labeled 1-6 are
source specific. For example, IR port "1"
must be mounted to the audio source
connected to "source input 1". The "ALL
IR OUT" port is constantly active, and
passes ALL IR 1-6 information, regard-
less of the source selected.
The AH66T is preprogrammed with the following scenes and
point to the Lutron Radio RA® 2 phantom buttons as shown.
Dealer must program the Lutron system scenes to match
this scenario before proper operation is achieved.
point to the Lutron Radio RA® 2 phantom buttons as shown.
Dealer must program the Lutron system scenes to match
this scenario before proper operation is achieved.
AH66T
Satellite
AIE2
Talk-Back
Emitter
DVD
A/V Receiver
Determine the best location for the AH66T and all audio source equipment (CD player, satellite, iPod, etc.)
Run a Cat-5 wire from each room (Zone) touchpad location to the AH66T
Run speaker wiring (16 gauge is recommended) from each speaker location back to the AH66T
Be sure to label all wires for easy identification
Turn off power to the AH66T (Disconnect from power source)
B – Terminate RJ-45 Plugs On Both Ends
Using a Cat-5
cable stripper,
remove about
1 - 1/2" of the
jacket as shown
above.
cable stripper,
remove about
1 - 1/2" of the
jacket as shown
above.
1 1/2"
1/2"
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Green/White
Orang
e/White
Blue/White
Bro
wn/White
Green
Blue
Orang
e
Bro
wn
Untwist the twist-
ed pair wires and
arrange them in
the order shown
above.
ed pair wires and
arrange them in
the order shown
above.
Press all wires
flat between your
thumb and index
fingers and cut
the wires so they
are 1/2" long as
shown above.
flat between your
thumb and index
fingers and cut
the wires so they
are 1/2" long as
shown above.
Insert the ar-
ranged wires into
the RJ-45 plug
as shown above.
The locking tab
is facing down in
this view.
ranged wires into
the RJ-45 plug
as shown above.
The locking tab
is facing down in
this view.
Finally, crimp the
connector using
a standard RJ-45
crimping tool.
connector using
a standard RJ-45
crimping tool.
1/4"
16AWG
Speaker Wire
To Speakers
+
+
+
+
– –
–
–
The AH66T is preconfigured with the following parameters and does not require PC programming
to operate. If customization is desired, visit www.atonhome.com to download SystemWorx, the
configuration software.
to operate. If customization is desired, visit www.atonhome.com to download SystemWorx, the
configuration software.
Audio Source 1: iPort® Dock
Audio Source 2: IR Source
Audio Source 3: IR Source
Audio Source 4: IR Source
Audio Source 5: IR Source
Audio Source 6: IR Source
Audio Source 7: Built-In AM/FM Tuner
Lights Page: Lutron RadioRA®2
Audio Source 2: IR Source
Audio Source 3: IR Source
Audio Source 4: IR Source
Audio Source 5: IR Source
Audio Source 6: IR Source
Audio Source 7: Built-In AM/FM Tuner
Lights Page: Lutron RadioRA®2
OLED Phantom RA2
Button Button
ALL ON
Button Button
ALL ON
1
DAY
3
PARTY
5
OLED Phantom RA2
Button Button
ALL OFF
Button Button
ALL OFF
2
NIGHT
4
AWAY
6