Atlas GUARDIAN PRO MLGS180B Benutzerhandbuch
-3-
598-1096-01
Motion
Least Sensitive
Most Sensitive
Sensor
Motion
The sensor is less sensitive to motion directly
towards it, most sensitive to motion across its field
of view.
towards it, most sensitive to motion across its field
of view.
Maximum Range
Maximum
Coverage Angle
8 ft.
(2.4m)
70 ft.
(21m)
TEST AND ADJUSTMENT
❒
Turn on the circuit breaker and light switch.
NOTE:
Sensor has a 1
1
/
2
minute calibration
period before it will detect motion. When
first turned on, wait 1
first turned on, wait 1
1
/
2
minutes.
RANGE
10 5 1 TEST
ON-TIME
Bottom of Sensor
Avoid aiming the control at:
• Objects that change temperature rapidly, such
as heating vents and air conditioners. These
heat sources could cause false triggering.
heat sources could cause false triggering.
• Areas where pets or traffic may trigger the control.
• Nearby large, light-colored objects reflecting
• Nearby large, light-colored objects reflecting
light may trigger the shut-off feature. Do not point
other lights at the sensor.
other lights at the sensor.
MIN
MAX
180
°
❒
Loosen the clamp screw in
the sensor ball joint and
gently rotate the sensor.
the sensor ball joint and
gently rotate the sensor.
❒
Walk through the cover-
age area noting where you
are when the lights turn on
(also, the LED will flash
several times when motion
is detected). Move the sen-
sor head up, down, or side-
ways to change the cover-
age area. Keep the sen-
sor at least 1" (2.5 cm)
away from the lamps.
age area noting where you
are when the lights turn on
(also, the LED will flash
several times when motion
is detected). Move the sen-
sor head up, down, or side-
ways to change the cover-
age area. Keep the sen-
sor at least 1" (2.5 cm)
away from the lamps.
❒
Adjust the RANGE as
needed. RANGE set too
high may increase false
triggering.
needed. RANGE set too
high may increase false
triggering.
❒
Secure the sensor head
by tightening the clamp screw. Do not over-
tighten the screw.
by tightening the clamp screw. Do not over-
tighten the screw.
❒
Set the amount of TIME you want the lights to stay
on after motion is detected (1, 5, or 10 minutes).
on after motion is detected (1, 5, or 10 minutes).
Clamp
Screw
Screw
Ball
Joint
Joint
Aim Sensor
Down for Short
Coverage
Aim Sensor
Higher for Long
Coverage
Warning - Risk of fire. Do not aim the lamps at
a combustible surface within 3 ft. (1 m).
a combustible surface within 3 ft. (1 m).
SPECIFICATIONS
Range . . . . . . . . . . . . . . Up to 70 ft. (21 m) [varies with
surrounding temperature].
Sensing Angle . . . . . . . . Up to 180
°
Electrical Load . . . . . . . . Up to 500 Watt (4.2A) Maxi-
mum Incandescent [Up to 250
Watt maximum each lamp
holder.]
Watt maximum each lamp
holder.]
Power Requirements . . . 120 VAC, 60 Hz
Operating Modes . . . . . . TEST, AUTO and MANUAL
Operating Modes . . . . . . TEST, AUTO and MANUAL
MODE
Time Delay . . . . . . . . . . 1 , 5, 10 minutes
Range . . . . . . . . . . . . . . Adjustable
Range . . . . . . . . . . . . . . Adjustable
Atlas Lighting Products, Inc. reserves the right to dis-
continue products and to change specifications at any
time without incurring any obligation to incorporate new
features in products previously sold.
continue products and to change specifications at any
time without incurring any obligation to incorporate new
features in products previously sold.
❒
Turn the RANGE control to the mid position and
the ON-TIME control to the TEST position.
the ON-TIME control to the TEST position.