DSCover Satellite Products Home Security System SCW904x Benutzerhandbuch

1.2 Wiring

1. Zone Wiring

Zones can be wired for Normally Open, Normally Closed Contacts with Single-
end-of-line (SEOL) resistors or Double End-of-Line (DEOL) resistors. Observe
the following guidelines

•

For UL/ULC listed installations use SEOL or DEOL only.

•

Minimum 22 AWG wire, maximum 18 AWG

•

Do NOT use shielded wire

•

Wire run resistance shall not exceed 100

Ω. Refer to the chart below.

•

Section [009] Selects Hardwired Zone Definition

•

Sections [133], [134] Opt [14] selects Normally Closed

•

Sections [133], [134] Opt [15] selects SEOL resistors

•

Sections [133], [134] Opt [16] selects DEOL resistors.

Zone Status - Loop Resistance/Loop Status
• Fault - 0

Ω (shorted wire/loop)

• Secure - 5600

Ω (contact closed)

• Tamper - infinite (broken wire, open)
• Violated - 11,200

Ω (contact open)

2. PGM/Aux Power Wiring

PGMs switch to ground when activated by control panel.
Connect the plus side of the device to be activated to the AUX+ Terminal. Con-
nect the minus terminal to the PGM. Each PGM can provide 50mA output.

NOTE: The control panel can provide a maximum of 100mA of AUX current for
PGMs, relays, LED’s etc. Min/Max operating voltages for PGMs, relays and
modules is 10.2V

- 13.75V

NOTE: Battery Voltage (6.0-8.4V

) is boosted internally to supply 12V

the AUX+ output by setting Sect[014] Opt[4] to ON. This option must be
enabled for PGMs used in UL/ULC Residential Burg installations. This output
can NOT be used for UL/ULC Fire installations.

LED output with
current limiting
resistor and
optional Relay
driver output

3. Telephone Line Wiring

Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an RJ-31x
Connector as indicated. Use 24 AWG wire minimum for wiring.

For connection of multiple devices to the telephone line, wire in the sequence
indicated.
Communication format is programmed in section [350].
Telephone Call Directions are programmed in section [351]-[376].

Note: For UL Listed Installations,the Installer must verify the communication format with the supervising station at the time of the installation.

4. Battery

5. AC Wiring

A 1500 mAHr Ni-Mh battery pack is included to meet standby power require-
ments
NOTE: UL/ULC Residential Burglary installations require 4 Hr. power standby
time plus 4 minutes alarm annunciation.
NOTE: UL/ULC Residential Fire installations require 24 Hr. power standby
plus 5 minutes alarm annunciation
NOTE: Battery life is 4-5 years under typical operating conditions. Battery
capacity deteriorates with age and number of charge/discharge cycles.
Replace battery every 4-5 years.

AC Transformer Requirements:

Primary:120VAC, 50/60Hz., 0.33A
240VAC, 50/60Hz., 0.165A
Secondary: 16.5VAC/20VA

The following Transformers shall be used:

UL Listed Installations - PTD1620U, PTD1640U (60Hz.)
ULC Listed installations - PTD1620, PTD1640 (60Hz.)
EU Installations - PTD1620T-EU (50 Hz.)

Burglary Zone Wiring Chart

Wire

Gauge

Max wire Length to End-of-line Resistor

(feet/meters)

3000 / 914

4900 / 1493

6200 / 1889

7800 / 2377

Figures are based on maximum wiring resistance of 100

Normally Closed Loops - Do NOT use for UL Installations

Single End-of-Line Resistor Wiring

Double End-of-Line Resistor Wiring

I/O

T-1

R-1
TIP

RING

RJ-31X

RED

GRN

BRN

GRA