Garmin Vector S Benutzeranleitung
9
Apply a layer of bike grease to the spindle.
10
Insert the spindle into the cartridge.
11
Wipe away any excess grease.
12
Install the new washer and nut on the end of the spindle.
NOTE: The nut for the right spindle has a left-handed
NOTE: The nut for the right spindle has a left-handed
(reverse) thread.
13
Use the hex nut driver to tighten the nut.
WARNING
Garmin recommends torque of 7 lbf-ft. (10 N-m). Failure to
properly tighten the nut could cause the pedal to fall off
during a ride, which could result in property damage or
serious bodily injury or death.
14
Install the new pedal by screwing it onto the cartridge until
there is no gap.
NOTE: The right pedal has a left-handed (reverse) thread.
NOTE: The right pedal has a left-handed (reverse) thread.
15
Replace the pedal pods and pedals according to the
installation instructions (
).
16
Rotate the crank arm to check for clearance and smooth
pedal rotation.
After you replace the pedals and cartridges, you must
recalibrate the system.
Vector Storage
If you are transporting your bicycle or not using Vector for an
extended period of time, Garmin recommends removing Vector
and storing it in the product box.
Vector Specifications
Battery type
User-replaceable CR2032, 3 volts
Battery life
Minimum 175 hours of riding time
NOTE: The pedal pod used on the right crank will
drain the battery faster than the left crank.
NOTE: The pedal pod used on the right crank will
drain the battery faster than the left crank.
Operating
temperature range
temperature range
From -4° to 122°F (from -20° to 50°C)
Water resistance
IPX7
NOTICE
Do not submerge or pressure wash the
components.
components.
Radio frequency/
protocol
protocol
2.4 GHz ANT+ wireless communications protocol
USB ANT Stick™ Specifications
Power source
USB
Operating temperature
range
range
From 14° to 122°F (from -10° to 50°C)
Radio frequency/protocol
2.4 GHz ANT+ wireless communications
protocol
protocol
Transmission range
Approximately 16.4 ft. (5 m)
Battery Information
Vector monitors the battery level of both pedal pods and sends
status information to your Edge device. When you receive a low
battery warning, you have approximately 10–20 hours of
operation time remaining.
Replacing the Pedal Pod Battery
WARNING
Do not use a sharp object to remove user-replaceable batteries.
Contact your local waste disposal department to properly
Contact your local waste disposal department to properly
recycle the batteries. Perchlorate Material – special handling
may apply. Go to
NOTE: Always replace both batteries at the same time.
1
Locate the circular battery cover
À
on the back of the pedal
pod.
2
Use a coin
Á
to twist the cover counter-clockwise, moving
the arrow from the locked
Â
to unlocked
Ã
.
3
Remove the cover.
You can use a piece of tape
You can use a piece of tape
Ä
or a magnet to remove the
battery from the cover.
4
Wait 30 seconds.
5
Insert the new battery into the cover, observing polarity.
6
Replace the cover, making sure the arrow points to
unlocked.
7
Use a coin to twist the cover clockwise back into place,
making sure the arrow points to locked.
8
Wait 10 seconds.
After you replace the pedal pod battery, you must set the
installation angle on your Edge (
Appendix
Registering Vector
Help us better support you by completing our online registration
today.
• Go to
• Go to
.
• Keep the original sales receipt, or a photocopy, in a safe
place.
Edge 810 and 510 Device Instructions
Pairing Vector with Your Edge 810 or 510 Device
1
Bring the Edge device within range (3 m) of the sensor.
NOTE: Stay 10 m away from other ANT+ sensors while
NOTE: Stay 10 m away from other ANT+ sensors while
pairing.
2
Turn on the Edge device.
3
From the home screen, select > Bike Profiles.
4
Select a profile.
5
Select .
6
Enable the sensor, and select Search.
7
Rotate the crank arm a few times.
Appendix
5