Barco Projector 26-0313000-00 Benutzerhandbuch
Encore Presentation System • User’s Guide • Rev 04
279
6. System Setup
Destination Setup
pÅêÉÉåmolJff=aÉëíáå~íáçå=pÉíìé
In this procedure, you will set up ScreenPRO-II systems as single screen destinations.
Once assigned, the associated button(s) on the Destination Bus will be active.
Once assigned, the associated button(s) on the Destination Bus will be active.
S
Prerequisites
— Ensure that you are familiar with the ways in which a
page 393 for details.
Use the following steps to set up a ScreenPRO-II destination:
1.
In the System Keypad, press SYSTEM to access the System Menu.
2.
Press
{
DEST SETUP
}
to display the Destination Setup Menu.
3.
On the Destination line, select the destination that you want to define.
4.
(Optional) If desired, press
{
REMOVE ALL}
to remove all previously assigned
Video Processors (VPs) from the selected destination.
5.
Scroll to the Type line and select Single Screen SP.
6.
Scroll to the SP to Add line and select the ScreenPRO-II ID that you wish to add.
7.
Press
{
ADD
}
to add the highlighted ScreenPRO-II. Once added, the ID appears
in the bottom portion of the menu.
8.
If required, scroll to the SP to Remove line, select the ID of the ScreenPRO-II that
you want to remove from the destination, and press
you want to remove from the destination, and press
{
REMOVE
}
.
9.
Scroll to the Routing Mode line and select Internal or External — depending on
the way that you want to configure your source routing. Please note:
the way that you want to configure your source routing. Please note:
~
When External routers are used, connect two outputs from an Analog
router to any two HD-15 inputs on the ScreenPRO-II. An SDI router
can also be connected to BNC inputs 1 and 2. During setup, these
specific patches will be defined using the Output Patch Menu.
router to any two HD-15 inputs on the ScreenPRO-II. An SDI router
can also be connected to BNC inputs 1 and 2. During setup, these
specific patches will be defined using the Output Patch Menu.
~
When Internal routing is used, connect Analog sources to inputs 1 - 8 on
the HD-15 connectors, and SDI sources to BNC inputs 1 and 2. During
setup, these patches will be defined using the Input Patch Menu.
the HD-15 connectors, and SDI sources to BNC inputs 1 and 2. During
setup, these patches will be defined using the Input Patch Menu.
10.
Repeat from step 3 for each additional ScreenPRO-II destination that you want to
set up.
set up.
This completes the procedure for defining ScreenPRO-II destinations. The selected
buttons on the Destination Bus are now active. Please note:
buttons on the Destination Bus are now active. Please note:
•
When a ScreenPRO II destination uses “external” routing, the OUTPUT PATCH
table for the external router allows you to choose which analog input on the
ScreenPRO II is being used by the router output. These procedures are covered
in the Router Setup section.
table for the external router allows you to choose which analog input on the
ScreenPRO II is being used by the router output. These procedures are covered
in the Router Setup section.
•
When a ScreenPRO II destination uses internal routing, you can patch individual
inputs, or you can define selected source buttons to use the same input for all
ScreenPRO IIs. This method is ideal if you are using D/As to connect sources to
similar inputs on each ScreenPRO-II. These procedures are covered in the Input
Patching
inputs, or you can define selected source buttons to use the same input for all
ScreenPRO IIs. This method is ideal if you are using D/As to connect sources to
similar inputs on each ScreenPRO-II. These procedures are covered in the Input
Patching
section.