Benq Thermometer sp870 Benutzerhandbuch
45
Maintenance
Eng
lish
lish
Extending lamp life
The projection lamp is a consumable. To keep the lamp life as long as possible, you can do the following settings
via the OSD menus.
•
via the OSD menus.
•
Setting Lamp Mode as Economic
Using Economic mode reduces system noise and power consumption. If the Economic mode is selected, the light
output will be reduced and result in darker projected pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set Economic mode, go into the
SYSTEM SETUP: Advanced > Lamp Settings > Lamp Mode menu and press / to select Economic.
•
output will be reduced and result in darker projected pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set Economic mode, go into the
SYSTEM SETUP: Advanced > Lamp Settings > Lamp Mode menu and press / to select Economic.
•
Setting Auto Power Off
This function allows the projector to turn off automatically if no input signal is detected after a set period of time
to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off menu and press / . The time
period can be set from 5 to 30 minutes in 5-minute increments. If the preset time lengths are not suitable for your
presentation, select Disable. The projector will not automatically shut down in a certain time period.
to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off menu and press / . The time
period can be set from 5 to 30 minutes in 5-minute increments. If the preset time lengths are not suitable for your
presentation, select Disable. The projector will not automatically shut down in a certain time period.
Timing of replacing the lamp
When the LAMP indicator light is red or a message appears suggesting it is time to replace the lamp, please install
a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances
the lamp may explode.
a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances
the lamp may explode.
The LAMP indicator light and TEMPerature indicator light will light up if the lamp becomes too hot. Turn
the power off and let the projector cool for 45 minutes. If the LAMP or TEMPerature indicator light still
lights up after turning the power back on, please contact your dealer. See
the power off and let the projector cool for 45 minutes. If the LAMP or TEMPerature indicator light still
lights up after turning the power back on, please contact your dealer. See
for
details.
The following Lamp warning displays will remind you to change the lamp.
"XXXX" shown in the above messages are numbers that vary depending on different models.
Status & Message
Status & Message
•
Install a new lamp for optimal performance. If the
projector is normally run with Economic Mode
selected (See
projector is normally run with Economic Mode
selected (See
), you may
continue to operate the projector until the next
lamp warning appears.
lamp warning appears.
•
A new lamp should be fitted to avoid the
inconvenience when the projector runs out of
lamp time.
inconvenience when the projector runs out of
lamp time.
•
It is strongly recommended that you replace the
lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished.
lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished.
•
The lamp MUST be replaced before the projector
will operate normally.
will operate normally.
OK
Order Replacement Lamp
Lamp > XXXX Hours
Notice
OK
Replace Lamp Soon
Lamp > XXXX Hours
Notice
OK
Replace Lamp Now
Lamp > XXXX Hours
Lamp usage time exceeded
Lamp usage time exceeded
Notice
OK
Lamp-usage time exceeded
Replace lamp (refer to user manual)
Then reset lamp timer
Then reset lamp timer
Notice