Windsor SUPREME ULTRA HIGH SPEED BURNISHER P1700120 Benutzerhandbuch

Seite von 4
SUPREME ULTRA 
HIGH SPEED 
BURNISHER 
SERVICE MANUAL 
AND PARTS LIST 
INSPECTION 
Carefully  unpack and  inspect  your  ma- 
chine for  shipping damage.  Each unit  is 
operated  and thoroughly inspected before 
shipment,  and  any  damage  is  the  re- 
sponsibility  of  the delivering carrier who 
should be notified immediately. 
ELECTRICAL 
This rotary polisher is designed 
to 
oper- 
ate on a standard 
15 
amp, 
115 
volt, 
hz, 
AC  household  current.  Check  that  the 
voltage  shown on  the  serial  number  plate 
is suitable for the supply available. Volt- 
ages below 
volts or above 
125 
volts 
could cause damage 
to the motor. 
WARNING:  To  avoid  electric  shock  do 
not expose to rain. Store indoors. 
GROUNDING  INSTRUCTIONS 
To  protect  the  operator from  electrical 
shock,  this  machine must be grounded 
while  in  use.  The  machine is equipped 
with  an  approved,  three-conductor 
power cord  and  three-prong grounding 
type  plug 
to  fit  the  proper  grounding 
type  receptacle. The 
is 
ped with a 
foot power cord. 
OPERATION 
1.  Plug machine  into the  power supply 
and check that the red indicator light 
(located on top of  switch housing) 
is 
on. 
You  will  notice  three  control  levers 
located at the top of the handle. The 
two  smaller  ones  directly  beneath 
the  handle  grips  control  the  onloff 
switches.  From the  operator's  posi- 
tion,  the  longer lever on  the  right  is 
used for 
the handle 
in position.' 
3.  With the handle locked in the upright 
position, tilt  the  machine  back  until 
the handle is resting on the floor  ex- 
posing the 
drive-pad. Install 
the  proper  high  speed  buffing  pad 
using  the 
pad 
holder to retain pad. 
4.  With the pad properly installed, return 
machine 
to the upright position. 
CAUTION:  To  prevent  possible dam- 
age to the pad or pad driver, remove 
buffing pad from  machine when  not 
in use. 
5.  Adjust  front  caster:  For 
pads 
turn  caster  adjusting  knob  counter- 
clockwise  t o   lower  machine.  For 
thick  pads  turn  clockwise  to  raise 
machine. 
NOTE:  When pad pressure is properly 
set, the machine will  start  instantly. 
It  too  much pressure  is 
an 
overload of  motor  will 
circuit breaker 
to trip. 
6.  Pull  up  on  the  adjusting  lever  and 
lower  the  handle  to  a  comfortable 
working  height.  Release  adjusting 
lever 
to 
lock 
handle 
in 
place. 
NOTE:  A  safety  switch  mounted 
in 
the handle 
will 
not  allow  machine 
to 
run  until  handle  is  lowered 
to  the 
operating position. 
For  best  results,  the  Supreme 
Speed  Burnisher should be operated 
a  straight  line 
forward  and  re- 
verse 
not  side 
to side as you would 
low speed polisher. 
The floor  polisher  is equipped with a 
circuit  breaker. The action of  the cir- 
cuit  breaker  is  entirely  dependent 
upon the  loading  of  the  brush  drive 
motor and will only trip under exces- 
sive overload conditions.  If the circuit 
breaker should  trip,  it  can  be  reset 
after 
20 
seconds by  pressing the  re- 
set  button on the  right  hand side of 
the motor housing. 
NOTE:  The  operator  should  correct 
the cause 
of 
overloading  before pro- 
ceeding. The most common cause is 
an  excessively  soiled  pad  which 
should be 
over, cleaned 
or re- 
placed. 
SERVICING 
A  full service inspection involves the 
in- 
spection  and testing  of  all  items  which 
affect operator safety, items which may 
require  adjustment  from  time 
to  time, 
and  items  subject  to  wear  which  may 
require replacement  in order  to  prevent 
a breakdown. 
Motor: 
The  motor  is  totally  enclosed, 
capacitor start, capacitor run with circuit 
breaker protection. 
All 
ball  bearings  are 
and  have 
enough  lubricant  for  the  life  of  the 
machine. 
Remove  motor  cover  occasionally  and 
blow dust and lint  from motor  housing. 
Wheels:  Periodically remove wheels and 
add silicone lubricant to axle. 
Motor 
Removal: 
1. 
Remove  high-flex drive  pad 
(4) 
screws. 
2.  Remove brush cover (6) screws. 
3. 
Release tension on belt tension  spring. 
4.  Remove motor mounting bolts 
(3). 
1.  Remove high-flex drive pad. 
2.  Remove brush cover. 
3. 
Release tension on 
belt 
tension spring. 
4.  Loosen nuts on  motor mounting studs 
-4 
or 
turns. 
5. 
Install  new  belt  and  readjust  belt 
tension as shown: 
The  trouble  shooting  guides  on  inside 
and  back  cover  have  been  categorized 
to  assist  you  in locating and  servicing 
problems  that  could  occur  during  the 
life of the 
Burnisher.