Whirlpool GW397LXUQ Anleitung Für Quick Setup

1. Remove storage drawer.

2. Remove access panel (2 screws) located on the rear wall, 

inside the storage drawer compartment.

3. Check the oven bake burner for proper flame. 

This flame should have a ½" (1.3 cm) long inner cone of 
bluish-green, with an outer mantle of dark blue, and should 
be clean and soft in character. No yellow tips, blowing or 
lifting of flame should occur.

4. If the oven bake flame needs to be adjusted, locate the air 

shutter near the center rear of the range. Use a flat-blade 
screwdriver to loosen the air shutter adjustment screw. 
Rotate the air shutter until the proper flame appears. Tighten 
air shutter adjustment screw.

5. Press CANCEL when finished. 

6. Reinstall access panel and oven bake burner cover.

1. Close the oven door.

2. Press the BROIL pad. “BROIL” and “SET” will flash in the 

display.

3. Press the PRESETS 0 number pad once to set HI Broil or 

twice to set LO Broil. 

The igniter used to light the oven broil burner will glow. Once the 
igniter is hot, the oven broil burner should light. Under certain 
conditions, it may take up to 60 seconds for it to light.

Look through oven window to check oven broil burner for proper 
flame. This flame should have a ½" (1.3 cm) long inner cone of 
bluish-green, with an outer mantle of dark blue, and should be 
clean and soft in character. No yellow tips, blowing or lifting of 
flame should occur.

1. Use a flat-blade screwdriver to loosen the air shutter 

adjustment screw on the air shutter located at the rear of the 
oven broil burner.

2. Adjust the air shutter as need. 

3. Tighten air shutter adjustment screw.

4. Press CANCEL when finished.

Replace oven racks in oven cavity. Replace storage drawer.

1. Fit the ends of the drawer glides into the rails in the range. 

2. Lift up the front of the drawer and gently push in to the first 

stop position.

3. Lift drawer up again and push until drawer is closed.

1. Check that all parts are now installed. If there is an extra part, 

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that the range is level. See the “Level Range” section.

5. Use a mild solution of liquid household cleaner and warm 

water to remove waxy residue caused by shipping material. 
Dry thoroughly with a soft cloth. For more information, see 
the “Range Care” section of the Use and Care Guide or User 
Instructions.

6. Read the Use and Care Guide or User Instructions.

7. Turn on surface burners and oven. See the Use and Care 

Guide or User Instructions for specific instruction on range 
operation. 

■

Household fuse is intact and tight, or circuit breaker has not 
tripped.

■

Range is plugged into a grounded 3 prong outlet.

■

Electrical supply is connected.

■

See “Troubleshooting” in the Use and Care Guide or User 
Instructions.

8. When the range has been on for 5 minutes, check for heat. If 

the range is cold, turn off the range and check that the gas 
supply line shutoff valve is open.

■

If the gas supply line shutoff valve is closed, open it, then 
repeat the 5-minute test as outlined above.

■

If the gas supply line shutoff valve is open, press the 
CANCEL button on the oven control panel and contact a 
qualified technician.

Please reference the “Assistance or Service” section of the Use 
and Care Guide or the cover of the User Instructions, or contact 
the dealer from whom you purchased your range.