Sanyo Washer SW-830XT Benutzerhandbuch
Troubles
Check list
Not washing
Not spinning
Not drainning
Over load
WASH TIMER is in
the "OFF"position.
the "OFF"position.
OFF
5
10
15
Power failure.
Fuse blown.
Fuse blown.
PULSATOR maybe
clogged.
clogged.
OFF
1
2
3
4
5
SPIN TIMER is in
the "OFF"position.
the "OFF"position.
LID not closed properly.
Laundry not distributed
evenly.
evenly.
DRAIN HOSE is not laid
down correctly.
down correctly.
DRAIN HOSE is
twisted.
twisted.
DRAIN HOSE frozen.
Too much
.
Power voltage too low.
laundry in the tub
Notes for spinning
Distribute laundry evenly in the
SPIN TUB as shown below.
SPIN TUB as shown below.
X
O
Put the SPINNER CAP inside
the tub as shown below.
the tub as shown below.
SPIN TUB
Laundry
O
X
X
X
OPERATING INSTRUCTIONS
TROUBLESHOOTING
3
4
MAINTENANCE
Unplug the POWER CORD
after operation.
after operation.
Wipe the washer clean and dry with
a soft cloth.
a soft cloth.
Cleaning of the WASH and SPIN TUB
is necessity after bleaching or starching,
otherwise, undesireable deposit will left over.
is necessity after bleaching or starching,
otherwise, undesireable deposit will left over.
Remove the LINT FILTER for cleaning.
Kinds of laundry
Washing
Time
Synthetic(thin)
Delicate fabrics
Delicate fabrics
Cotton
Linen
Linen
Heavily soiled clothes
Thick clothes
Thick clothes
Blanket
2 to 5 min.
5 to 10 min.
10 to 15 min.
5 min.
Washing
Rinsing
Spin drying
Drainning
1. Transfer the laundry to the SPIN TUB, and place the SPINNER CAP on the top of laundry.
2. Close the INNER and OUTER SPIN TUB LID.
3. Turn the SPIN TIMER to 1 minute position.
4. Transfer the laundry to the WASH TUB after spin drying.
5. Set the WASH SELECTOR to GENTLE or NORMAL position.
6. Let water flow into the WASH TUB and rinse for another 3 to 5 minutes. Repeat it 2 to 3 times.
7. When finish washing, make sure the WASH TIMER is at the “OFF” position, then turn WASH
SELECTOR to DRAIN position.
2. Close the INNER and OUTER SPIN TUB LID.
3. Turn the SPIN TIMER to 1 minute position.
4. Transfer the laundry to the WASH TUB after spin drying.
5. Set the WASH SELECTOR to GENTLE or NORMAL position.
6. Let water flow into the WASH TUB and rinse for another 3 to 5 minutes. Repeat it 2 to 3 times.
7. When finish washing, make sure the WASH TIMER is at the “OFF” position, then turn WASH
SELECTOR to DRAIN position.
1. Transfer the laundry to the SPIN TUB and place
the SPINNER CAP on the top of the laundry.
2. Close the INNER and OUTER SPINNER LID.
3. Turn the SPIN TIMER knob to the desired dry time
position. Then spin-dry will start.
the SPINNER CAP on the top of the laundry.
2. Close the INNER and OUTER SPINNER LID.
3. Turn the SPIN TIMER knob to the desired dry time
position. Then spin-dry will start.
Kinds of laundry
Spin-drying time
Wool articles
30 seconds
1 minute
1 to 3 minutes
3 minutes
3 to 5 minutes
5 minutes
Thin articles(synthetic)
Sweater(synthetic)
Blanket(synthetic)
Underwear(cotton)
Sheet(towel fabric)
Make sure water is turned off when spin-drying for safety reason.
1. Set the WASH SELECTOR to GENTLE or NORMAL
position.
2. Turn on the water tap, let water flow into the WASH TUB
in accordance with the amount of laundry to be washed.
(The marks H, M, L in tub are High, Medial, Low water
level.)
3. Add proper amount of detergent.
4. Put laundry into the WASH TUB.
5. Turn the WASH TIMER knob to the desired wash time
position, and washing action will start.
6. When finished, make sure the WASH TIMER is at
the “OFF” position, then turn WASH SELECTOR to
DRAIN position.
position.
2. Turn on the water tap, let water flow into the WASH TUB
in accordance with the amount of laundry to be washed.
(The marks H, M, L in tub are High, Medial, Low water
level.)
3. Add proper amount of detergent.
4. Put laundry into the WASH TUB.
5. Turn the WASH TIMER knob to the desired wash time
position, and washing action will start.
6. When finished, make sure the WASH TIMER is at
the “OFF” position, then turn WASH SELECTOR to
DRAIN position.
<Without pump model>
1. Lay down the DRAIN HOSE and turn the WASH SELECTOR to DRAIN.
<With pump model>
1. Position the DRAIN HOSE to a wash-basin or drain outlet at the height of lower than 1 meter.
2. Turn the WASH SELECTOR to DRAIN position, and the PUMP will then begins to work to drain away the water.
3. If you wish to drain the water while spinning, turn the SPIN TIMER, and the SPIN TUB will starts rotating and
the pump will starts working at the same time.
4. If you find the PUMP is working but there is no water drained away, lay down the DRAIN HOSE once, and it
will start draining away the water. Hook the DRAIN HOSE again at the wash-basin or drain outlet.
5. When draining is over, turn off the power.
1. Lay down the DRAIN HOSE and turn the WASH SELECTOR to DRAIN.
<With pump model>
1. Position the DRAIN HOSE to a wash-basin or drain outlet at the height of lower than 1 meter.
2. Turn the WASH SELECTOR to DRAIN position, and the PUMP will then begins to work to drain away the water.
3. If you wish to drain the water while spinning, turn the SPIN TIMER, and the SPIN TUB will starts rotating and
the pump will starts working at the same time.
4. If you find the PUMP is working but there is no water drained away, lay down the DRAIN HOSE once, and it
will start draining away the water. Hook the DRAIN HOSE again at the wash-basin or drain outlet.
5. When draining is over, turn off the power.