Phase Technology ATS-1 Benutzerhandbuch
SPECIFICATIONS
Tweeter
1” soft dome
Woofer
4” mineral fi lled cone with butyle rubber surround
Shielding
Video shielded
Crossover
12 dB per octave @ 2.5 kHz
Frequency
80 Hz - 20 kHz + 3 dB
Amp Power
80 Watts continuous
Sensitivity
90 dB
Impedence
6 Ohms
Dimensions*
6 7/8” H x 8 1/8” W x 6 3/8” D
Finish
Black or white
* All measurements include the base /mount assembly.
Phase Technology Corporation 6400 Youngerman Circle Jacksonville, Florida 32244 1.888.PHASE TK www.phasetech.com
Note: For ceiling or wall mounting, it is recommended to center the base on a stud or wood frame member within
your structure whenever possible. Once the base is properly secured, the speaker may be replaced on the mounting
post.
your structure whenever possible. Once the base is properly secured, the speaker may be replaced on the mounting
post.
Before you replace the speaker on the mounting post, connect the speaker wire to the terminals on the back of
the speaker. Once you have connected the wire, place the speaker on the mounting post and replace the retaining
collar and screws using the allen wrench. Hold the speaker at the desired angle and tighten the screws. Avoid over-
tightening the screws. Always loosen the retaining screws before attempting to change the speaker angle.
the speaker. Once you have connected the wire, place the speaker on the mounting post and replace the retaining
collar and screws using the allen wrench. Hold the speaker at the desired angle and tighten the screws. Avoid over-
tightening the screws. Always loosen the retaining screws before attempting to change the speaker angle.
RUBBER FEET
Peel-and-stick rubber feet are provided for the bottom of the base. It is recommended that the feet be applied to the
base when using the ATS-1 on a shelf of other fl at surface to prevent marring the surface and to prevent the ATS-1
from sliding due to vibration.
base when using the ATS-1 on a shelf of other fl at surface to prevent marring the surface and to prevent the ATS-1
from sliding due to vibration.
CARING FOR YOUR SPEAKERS - OUTDOOR USE
Your ATS-1 speakers are engineered for both indoor and outdoor use and operation. Random water hitting the
speaker will not damage your ATS-1, making it ideally suited for placement in close proximity to swimming pools and
spas. The ATS-1 is not intended for use underwater, however.
speaker will not damage your ATS-1, making it ideally suited for placement in close proximity to swimming pools and
spas. The ATS-1 is not intended for use underwater, however.
Ordinary dust and dirt accumulation will not harm the ATS-1. If you wish to clean the ATS-1, household glass cleaning
solution sprayed on a paper towel may be used for light cleanup. For heavier stains, a soap and water solution
applied with a rag or sponge should remove the dirt and stains. Avoid spraying the ATS-1 with a high-pressure hose.
solution sprayed on a paper towel may be used for light cleanup. For heavier stains, a soap and water solution
applied with a rag or sponge should remove the dirt and stains. Avoid spraying the ATS-1 with a high-pressure hose.
SERVICE ISSUES AND WARRANTY
Phase Technology has an uncompromising commitment to quality assurance. In the unlikely event that a problem
occurs with your ATS-1, please contact your Phase Technology dealer. Your new ATS-1 comes with a warranty to
protect you, the original purchaser, for a period of ten years again defects in material and workmanship. Please refer
to the warranty card included with this manual.
occurs with your ATS-1, please contact your Phase Technology dealer. Your new ATS-1 comes with a warranty to
protect you, the original purchaser, for a period of ten years again defects in material and workmanship. Please refer
to the warranty card included with this manual.
6