Allmand Marine Lighting 8330 Benutzerhandbuch
8
MANUAL WINCH MAST OPERATION
ALWAYS CHECK FOR OVERHEAD
OBSTRUCTIONS BEFORE RAISING
AND LOWERING MAST. ALLOW 35'
CLEARANCE. AVOID ALL OVERHEAD
ELECTRICAL WIRES
OBSTRUCTIONS BEFORE RAISING
AND LOWERING MAST. ALLOW 35'
CLEARANCE. AVOID ALL OVERHEAD
ELECTRICAL WIRES
.
TO PREVENT INSTABILITY AND HELP
ENSURE SAFE OPERATION, ALWAYS
PROVIDE PROPER GROUND SUP-
PORT BEFORE RAISING MAST.
ENSURE SAFE OPERATION, ALWAYS
PROVIDE PROPER GROUND SUP-
PORT BEFORE RAISING MAST.
BEFORE RAISING MAST, VISUALLY
INSPECT EQUIPMENT FOR DAMAGE
OR WEAR. FAMILIARIZE YOURSELF
WITH THE LOCATION AND FUNCTION
OF ALL OPERATING PARTS BY STUDY-
ING THIS MANUAL. OBSERVE ALL
CAUTION DECALS LOCATED ON
EQUIPMENT
INSPECT EQUIPMENT FOR DAMAGE
OR WEAR. FAMILIARIZE YOURSELF
WITH THE LOCATION AND FUNCTION
OF ALL OPERATING PARTS BY STUDY-
ING THIS MANUAL. OBSERVE ALL
CAUTION DECALS LOCATED ON
EQUIPMENT
NOTE: The latch locks the mast in the
vertical position and disengages the
sections allowing the tower assembly
to be rotated to position the lights.
vertical position and disengages the
sections allowing the tower assembly
to be rotated to position the lights.
!
SAFETY
WARNING
DESCRIPTION OF OPERATION
The Allmand NIGHT-LITE 6330 tower
assembly consists of a three section tele-
scoping mast which can be raised and
extended by operating two hand crank
winches. One winch, mounted with the
handle extending through the side of the
trailer frame, raises and lowers the mast
from the horizontal towing position, the
vertical position, and back. The second
winch mounted on the tower extends the
telescopic sections.
assembly consists of a three section tele-
scoping mast which can be raised and
extended by operating two hand crank
winches. One winch, mounted with the
handle extending through the side of the
trailer frame, raises and lowers the mast
from the horizontal towing position, the
vertical position, and back. The second
winch mounted on the tower extends the
telescopic sections.
The three section mast assembly can be
rotated from the ground by loosening a
knob and rotating the entire assembly 360°
to aim the lights as necessary.
rotated from the ground by loosening a
knob and rotating the entire assembly 360°
to aim the lights as necessary.
TO ERECT MAST AND RAISE
LIGHTS
LIGHTS
1. Extend both side outrigger jacks, rear jack
and tongue jack to stabilize and level the
trailer.
trailer.
NOTE: Jacks should be placed only on
firm footing.
firm footing.
WHEN EXTENDING REAR JACK, WATCH
TO ENSURE YOU ARE CLEAR OF THE
OVERHANGING ENDS OF THE MAST
BEFORE YOU STAND UP
OVERHANGING ENDS OF THE MAST
BEFORE YOU STAND UP
.
THE SUPPLEMENTAL GROUND ROD IS A
SAFETY DEVICE THAT MAY REDUCE
THE CHANCE OF PERSONAL INJURY
FROM STRAY ELECTRICAL CURRENT
THE CHANCE OF PERSONAL INJURY
FROM STRAY ELECTRICAL CURRENT
.
Therefore, Allmand recommends using
the ground rod. However, it is the user’s
responsibility to determine the require-
ments and/or applicability of local, state,
or national electrical code which governs
the use of the ground rod.
the ground rod. However, it is the user’s
responsibility to determine the require-
ments and/or applicability of local, state,
or national electrical code which governs
the use of the ground rod.
!
SAFETY
WARNING
2. Attach the ground rod to the grounding lug,
and drive the ground rod fully for adequate
electrical ground, as required by local,
state, or national code.
electrical ground, as required by local,
state, or national code.
3. Release the pin that secures the mast to
the rear mast support.
4. Operate the hand crank on the side of the
trailer to raise the mast from horizontal to
vertical.
vertical.
5. Turn black knob counterclockwise and
engage latch in strike plate. Retighten black
knob.
knob.
6. Operate the hand crank winch on the tower
clockwise to raise the lights vertically.
7. To rotate the lights, release the black knob
and turn the tower assembly with the
handles provided.
handles provided.
8. To turn on lights, flip the breaker switches to
the up position. (SEE FIG. 1)