Metronic ZAP 4 EVOLUTION 5 Benutzerhandbuch

Seite von 42
FOREWORD
Thank you for choosing a universal METRONIC remote. We are confident you will be fully sa-
tisfied with this product. Models ZAP 2 to 6 enable to manage 2 to 6 appliances: TV, Satellite 
receiver (SAT), DVD recorder (DVD) or HIFI system (AUX), DVB-T set top box (TNT), ADSL box 
(BOX) according to models. After inserting the 1.5V AAA batteries (not included) in the remote, 
you can set up the remote for each appliance that you wish to control. The universal METRONIC 
remote has been conceived to control most products of each brand. This is why you have the 
choice between 2 types of set ups : by Brand code or by automatic search. In the set up details 
below, we use a TV as example. In order to set up the remote for your DVB-T set top box or DVD 
recorder, replace ‘TV’ with ‘TNT’ or ‘DVD’. After you have set up the remote, simply press the TV, 
TNT, DVD etc key to select the appliance you wish to control.
A - Set up by brand code
1 - Switch on your TV. 
2 - Look up in the following pages the codes that correspond to the brand of your TV (i.e. for AEG, 
you should try the code 0589, then 1423 if the first code does not work, and finally 0043 if none 
of the two first codes work). 
3 - Press the PROG and TV keys together for a few seconds until the light switches on. If you wait 
too long before pressing another key, the remote will go into standby and the light will switch 
off. You should then start at Step 3.
4 - Enter one of the 4-digit Brand codes. After each digit, the light will briefly switch off. It will 
switch off for good after you have entered the 4th digit.  If the light blinks twice and then stays 
on, try the next code. 
5 - Point the remote towards your TV and try using the main features (changing channels, ad-
justing sound…) 
6 - If the remote does not control the TV properly, try the set up again (from 3) with the next 
Brand code. If the remote controls the TV correctly, then the set up is over. If the remote does 
not work properly with any code, you should try an automatic search. 
B - Automatic Search
1 - Switch on your TV. The automatic search might take a little while (up to 15 minutes). 
2 - Press the PROG and TV keys together for a few seconds until the light switches on. When you 
release the keys the light should stay on.  
3 - Press the PROG key. The light should start blinking. Press the    key until the light switches off 
and slowly starts blinking again. This means the automatic search has started.  The light should 
stay on and blink every time a new code is entered.  You should be ready to press the 0 key.  
4 - As soon as the TV switches off, press the 0 key. The light should start blinking. Press the TV key. 
The light should switch off. Note: You should be quick enough not to exceed 1 second before 
the next code from your remote control (a bit less than 1 second between turning TV off and 
time to press key «0»). 
5 - As your TV is now switched off, switch it on again using the original remote or with the front 
keys. 
6 - Point the remote towards your TV and try using the main features (changing channels, adjus-
ting sound…). If the remote does not control the TV properly, try the automatic set up again 
(from 2). If the remote controls the TV correctly, then the set up is over. 
Changing batteries
When the remote starts struggling to control the appliances or if it does not work properly, 
you should try changing batteries. Thanks to its memory function, you can change batteries 
withouht losing your settings on the remote. 
  GB | 
4 in 1 UNIVERSAL REMOTE CONTROL