Whirlpool WFC340S0A Installationsanweisungen

3. If the rear of the range lifts more than ½" (1.3 cm) off the floor 

without resistance, stop tilting the range and lower it gently 
back to the floor. The range foot is not engaged in the anti-tip 
bracket.

IMPORTANT: If there is a snapping or popping sound when lifting 
the range, the range may not be fully engaged in the bracket. 
Check to see if there are obstructions keeping the range from 
sliding to the wall or keeping the range foot from sliding into the 
bracket. Verify that the bracket is held securely in place by the 
mounting screws.

4. Slide the range forward, and verify that the anti-tip bracket is 

securely attached to the floor or wall.

5. Slide range back so the rear range foot is inserted into the 

slot of the anti-tip bracket.

IMPORTANT: If the back of the range is more than 2" (5.1 cm) from 
the mounting wall, the rear range foot may not engage the bracket. 
Slide the range forward and determine if there is an obstruction 
between the range and the mounting wall. Changes to the gas 
supply must be performed by a qualified service technician. If you 
need assistance or service, refer to the “Assistance or Service” 
section of the Use and Care Guide, or the cover or “Warranty” 
section of the User Instructions, for contact information.

6. Repeat steps 1 and 2 to ensure that the range foot is 

engaged in the anti-tip bracket.

If the rear of the range lifts more than ½" (1.3 cm) off the floor 
without resistance, the anti-tip bracket may not be installed 
correctly. Do not operate the range without anti-tip bracket 
installed and engaged. Please reference the “Assistance or 
Service” section of the Use and Care Guide, or the cover or 
“Warranty” section of the User Instructions, to contact service.

Determine if you have AquaLift™ Technology or Steam Clean by 
referring to the “Range Care” section of the User Instructions. 

1. Place level on the oven bottom as indicated in one of the two 

figures below depending on the size of the level. Check with 
the level side to side and front to back.

2. If range is not level, pull range forward until rear leveling leg is 

removed from the anti-tip bracket.

3. Follow the directions in Style 1 or Style 2, depending on the 

style of drawer supplied with the range.

1. Place a standard flat rack in oven. 

2. Place level on the rack and check levelness of the range, first 

side to side; then front to back.

3. If range is not level, pull range forward until rear leveling leg is 

removed from the anti-tip bracket. 

4. Follow the directions in Style 1 or Style 2, depending on the 

style of drawer supplied with the range.

Use

 a ¼" drive ratchet, wrench or pliers to adjust leveling legs 

up or down until the range is level. Push range back into 
position. Check that rear leveling leg is engaged in the anti-tip 
bracket.

Use a wrench or pliers to adjust leveling legs up or down until 
the range is level. Push range back into position. Check that 
rear leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking 
performance and best cleaning results using AquaLift™ 
Technology and Steam Clean functions.

Remove all items from inside the warming drawer or premium 
storage drawer, and allow the range to cool completely before 
attempting to remove the drawer.

1. Open the warming drawer or premium storage drawer to its 

fully open position.

2. Using a flat-blade screwdriver gently loosen the warming 

drawer or premium storage drawer from the glide alignment 
notch and lift up the drawer alignment tab from the glide.

3. Repeat Step 2 on the other side. The warming drawer or 

premium storage drawer is no longer attached to the drawer 
glides. Using both hands, pick up the warming drawer or 
premium storage drawer to complete the removal.

A

B

C