Kraus CGV39019MM1005SN Installationsanweisungen

Dear Valued Customer,

Kraus would like to take this opportunity 
to thank you for purchasing Kraus 
products. It is our sincere hope that you 
are completely satisfied with your new 
purchase. We welcome any questions or 
comments you may have, and look 
forward to assisting you in the future.
 
Sincerely,
Kraus Customer Service Department.

AB1953 Compliant

Adjustable wrench

Pipe  tape

Groove joint plier

Phillips screwdriver

If you've followed the instructions carefully and your faucet still does not work properly, take these corrective steps.

Check to make sure you have the following parts indicated below: 

Leakage under the handle.

Adjusting ring or cap has come loose.

Tighten the adjusting ring or cap. 

Aerator leaks or has an inconsistent 
water flow pattern.

Aerator is dirty or misfitted. 

Unscrew the aerator to  check rubber packing
or replace the aerator.

Water will not shut off completely.

• If you use soldering during the faucet installation, the seats, cartridges and washers must be 

   removed before using the flame. Otherwise, warranty will be void on these parts. 

• Cover your drain to avoid loosing parts. 

Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh chemicals as these 
will dull the finish and void your warranty.

Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh chemicals as these 
will dull the finish and void your warranty.

Shut off main water supply before installation.

Model

Hex wrench 

Dirty or worn out plastic washer in the
cartridge.

Remove the handle and the cartridge to check if the ceramic 
dish is dirty or permanently damaged. 

Keep this manual for ordering replacement parts.

 Silicone Sealant

The fittings should be installed by a licensed plumber.

KRAUS is proud to offer its customers the strongest, most durable 
c e r a m i c  c a r t r i d g e s  i n  a l l  s o l i d  b r a s s  K i t c h e n  F a u c e t s  i t 
manufactures. KRAUS guarantees all of our products to be free of 
defect in materials and craftsmanship. All KRAUS BRAND Kitchen 
Faucets carry a limited lifetime warranty from the original date of 
purchase.
 
If a product fails due to defect in material or craftsmanship during 
the warranty period, KRAUS will repair or replace the items at our 
sole discretion. Warranty does not apply when the item has been 
tampered with, misused, improperly installed, altered, or damaged 
due to abuse or accident. Proof of purchase (original sales receipt) 
must be provided to KRAUS for all warranty claims. Please contact 
one of our representatives if you need any additional details.

All KRAUS products must be installed by a licensed professional 
plumber or contractor to avoid any improper use or installation.
 
IN NO EVENT SHALL KRAUS BE LIABLE FOR ANY INCIDENTAL, 
CONSEQUENTIAL OR SPECIAL DAMAGES, INSTALLATION 
COST, LABOR, TRAVEL TIME, FREIGHT COSTS INCURRED, LOST 
PROFITS, OR CONTINGENT LIABILITIES.
 
KRAUS USA Inc. makes no representation that its products 
comply with any or all local building or plumbing codes. It is the 
consumer’s responsibility to determine local code compliance.
 
This warranty extends to the original purchaser and first 
consumer.

Install faucet body and base trim 
ring through top of sink.    

From underneath the sink,replace 
mounting hardware assembly.Tighten 
lock nut to secure the body. 

Apply pipe tape on threads of the 
inlet port. Tighten end of shank with 
wrench and slip hose into the inlet 
port.

Apply pipe tape onto threads 
of the water supply. Tighten the 
hose onto water supply.

After installing faucet, remove aerator    and 
turn on water to remove any left of debris.
Re-assemble aerator. 

 

1.

2.

3.

4.

5.

6.

7.

9.

8.

1  Handle Cap
2  Metal Handle
3  Trim Cap
4 Locking 

Nut

5  Ceramic Disc Cartridge
6   Base Trim Ring
7  Mounting Hardware Assembly
8 Aerator
9   Cover Plate & Putty Plate