Maytag MHN30PDCWW Installationsanweisungen

NOTE: After the washer has been installed and plugged in,  

the display may show ‘0 MINUTES’. Once the washer has been 

plugged in and the washer door opened and closed, the display 

will show the price. In washers set for free cycles, the display will 

flash ‘SELECT CYCLE’.

1.  PD Models: Insert coins until ‘SELECT CYCLE’ flashes  

in display.

    PR Models: A debit card is required rather than coins. In  

Enhanced Debit mode, the card balance will also display 

when a debit card is inserted into the reader.

2.  Door must be closed before cycle selection is made,
3.    Press fabric setting button for the wash cycle desired. After 

the cycle is started, the time will display and count down.

4.  If a cycle is interrupted by opening the door, ‘RESELECT 

CYCLE’ will flash in the display. To restart the washer,  

close door, and reselect desired cycle.

This condition indicates the washer is inoperative.
‘0 MINUTES’ SHOWING IN DISPLAY 

This indicates the cycle is complete and the washer cannot be 

operated. Coins dropped or debit inputs during this condition will 

be stored in escrow but cannot be used until normal operation  

is restored by opening and closing the door. If a door switch fails,  

it must be replaced before normal operation can be restored.
COLD START (Initial first use) 

Washer is programmed at the factory as follows:

11-minute wash period
3 rinses (extra rinse not enabled)
$1.75 wash price (PD models)
$0 00 wash price (PR models)

WARM START (after power failure) 

A few seconds after power is restored, if a cycle was in progress  

at the time of the power failure, ‘RESELECT CYCLE’ will flash  

in the display, indicating the need for a key press to restart the 

washer.
DOOR LOCK 

Prior to beginning a cycle, there is a door lock routine of lock/

unlock/relock; then cycle begins. The door will remain locked 

until the end of a cycle or approximately 2 minutes after a power 

interruption.
PRICING 

After the door is opened following the completion of a cycle,  

the display indicates the cycle price (unless set for free operation). 

As coins are dropped or debit inputs arrive, the display will change 

to lead the user through the initiation of a cycle.
FREE CYCLES 

This is established by setting the cycle price to zero. When this 

happens, ‘SELECT CYCLE’ will appear rather than a cycle price.

This washer is debit card ‘cable’ ready. It will accept a variety of 

debit card systems, but does NOT come with a debit card reader. 

Refer to the debit card reader manufacturer for proper washer  

set-up. In models converted to a Generation 1 debit card system, 

debit pulses represent the equivalent of one coin (coin 1).

IMPORTANT: Read all instructions before operating.
PD Models: Insert access door key, turn, and lift to remove  

access door.
PR Models: Once the debit card reader is installed (according 

to the reader manufacturer’s instructions), the set-up mode can 

only be entered by inserting a set-up card (supplied by the reader 

manufacturer) into the card slot. If a set-up card is not available, 

diagnostic modes can be entered by removing connector AA1 on 

the circuit board or by using the Service Access Code (see Service 

Access Code section, page 13) for PR models set up as a PN.
The lower fabric setting buttons and the digital display are used 

to set up the controls.
The display can contain 4 numbers and/or letters and a decimal 

point. These are used to indicate the set-up codes and related 
code values available for use in programming the washer.

1.   The PERM PRESS button is used to adjust the values 

associated with set-up codes. Pressing the button will change 

the value by increments. Rapid adjustment is possible by 

holding down the button.

2.   The WOOLENS button will advance through the set-up codes. 

Pressing the button will advance to the next available set-up 

code. Holding the button down will automatically advance 

through the set-up codes at a rate of 1 per second.

3.   The DELICATES AND KNITS button is used to select or 

deselect options.

Before proceeding, it is worth noting that, despite all of the 

options available, an owner can simply choose to uncrate a new 

commercial washer, hook it up, plug it in, and have a washer that 

operates.
Washers are preset at the factory for an 11-minute wash period 

and 3 rinses (no extra rinse).

 

■

The WOOLENS button will advance you from code to code.

 

■

The PERM PRESS button will change the code value.

 

■

The DELICATES AND KNITS button will select or deselect 

options.

FOR PR MODELS: The set-up codes are the same as for the 

“PD” model except where noted.
The set-up code is indicated by the one or two left-hand 

characters. The set-up code value is indicated by the two or 

three right-hand characters.