Maytag MHN30PDCWW Installationsanweisungen

1.  Open the washer door and remove any clothing or items  

from the washer.

2.  Inspect inner glass door. If debris is present, wipe off debris 

using damp cloth.

3.  Inspect the colored seal/bellow between the door opening 

and the drum for stained areas. Pull back the seal/bellow  

to inspect all areas under the seal/bellow and to check  

for foreign objects.

4.  If stained areas are found, wipe down these areas of the seal/

bellow, using the procedure that follows:

 a)  Mix a dilute solution, using ¾ cup (177 mL) of liquid    

 

chlorine bleach, and 1 gal. (3.8 L) of warm tap water.

 b)  Wipe the seal/bellow area with the dilute solution,  

 

using a damp cloth.

 c)   Let stand 5 minutes.
 d)    Wipe down area thoroughly with a dry cloth and let  

the washer interior air dry with door open.

 

■

Wear rubber gloves when cleaning for prolonged periods.

 

■

Refer to the bleach manufacturer’s instructions for proper use.

This washer has a special cycle that uses higher water volumes 

in combination with liquid chlorine bleach to thoroughly clean  

the inside of the washer.
NOTES:

 

■

Read these instructions completely before beginning  

the cleaning process.

 

■

If necessary, the cleaning cycle may be interrupted by 

pressing the DELICATES AND KNITS button twice. However, 

this will not immediately stop the cycle. The washer will 

continue with several rinse and drain steps to ensure that all 

remaining bleach is rinsed from the washer.

1.  Open the washer door and remove any clothing or items  

from the washer.

2.  Use liquid chlorine bleach: 

Open the dispenser drawer and immediately add 

2

⁄

3

 cup (160 mL) of liquid chlorine bleach to the bleach  

compartment.

 

NOTE: Do not add any detergent to this cycle. Use of more 

than 

2

⁄

3

 cup (160 mL) of bleach will cause product damage  

over time.

3.  Close the washer door and the dispenser drawer.
4.  To start the Clean Washer cycle, first enter “Start Operating 

Set-up.” Then press and hold DELICATES AND KNITS for 

1 second. With the entire display flashing, press BRIGHTS.

 

NOTE: The door will lock, the drum will rotate a ½ turn,  

then the door will unlock, lock again, and then the cycle  

will continue.

 

■

The washer will not fill, but the drum will rotate while 

the washer runs a short sensing cycle. This will take 

approximately 3 minutes.

5.  The cycle will determine whether clothing or other items are  

in the washer.

 a)  If no items are detected in the washer, it will proceed  

 

to Step 7.

 b)  If any items are detected in the washer, “rL” or “F-34”  

 

will be displayed. Then the door will unlock.

 

■

Press DELICATES AND KNITS to cancel the failure code. 

Then repeat steps 1, 3, and 4 to start the cycle again.

6.  Once the cycle has begun, allow the cycle to complete.
7.  After the cycle is complete, leave the door open slightly,  

to allow for better ventilation and drying of washer interior.

 

■

Use only “HE” High Efficiency detergent.

 

■

Leave the door slightly open after each cycle to allow  

for better ventilation and drying of washer interior.

 

■

Clean the washer monthly using the Washer Maintenance  

Procedure and 

2

⁄

3

 cup (160 mL) of liquid chlorine bleach.

 

■

If the procedure does not sufficiently improve the washer  

freshness, please evaluate your installation and usage 

conditions for other causes.

Use a soft damp cloth or sponge to wipe up any spills. 

Occasionally wipe the outside of your washer to keep it looking 

new. Use mild soap and water. Do not use abrasive products.

The dispenser drawer is removable for easy cleaning.

1.  Unlock the dispenser drawer by pressing the Release Lever. 

Remove the drawer.

2.  Remove the inserts (the siphon from the softener and bleach 

compartments).

3.  Wash the parts under running water.
 NOTE: Do not wash components in the dishwasher.
4.  Re-install the inserts and return the dispenser to the drawer.

Replace water inlet hoses after 5 years of use to reduce the risk 

of hose failure. Periodically inspect and replace water inlet hoses 

if bulges, kinks, cuts, wear, or leaks are found.
When replacing your water inlet hoses, mark the date  

of replacement.

If you need assistance:
Contact the distributor where the washer was purchased; locate 

an authorized Maytag Commercial Laundry distributoror or visit 

www.maytagcommerciallaundry.com.
When you call, have the washer model number and serial 

number. Both numbers can be found on the serial-rating plate 

located on your washer.