Dacor RNR30NFC Designanleitung
All specifications subject to change without notice.
Phone: (800) 793-0093
www.dacor.com
PLANNING
GUIDE
RNR30NS, RNR30NFS, RNR30NIS, RNR30NIFS
Renaissance
30” Wide
Electric Induction Range
Document # PG05-011
Revised 01/28/15 Page 5/5
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.
2
To create a “built-in look” on the front of the cabinet, this
dimension may be changed to 29 1/4” (74.3 cm), with the
width at the notches remaining 30 1/16”. This configuration
is only for models RNR30NIS and RNR30NIFS with side
panels behind door removed.
Countertop height: 34 3/4” (88.3 cm) min.
36 7/8” (93.7 cm) max.
Countertop thickness: 1 5/8” (4.1 cm) max.
■
Trim kit PN ATKR30SR is required for proper installation of a
downdraft vent with this range.
■
The self-rimming installation of the RNR30NI[F]S range and ERV3015
downdraft vent create a “built-in” look where the range trim overlaps
the countertop on both sides and the downdraft vent trim overlaps the
countertop in back. The ATKR30SR trim kit, installed on the back of
the range, will cover the front of the downdraft vent chassis.
■
Observe all vertical cabinet clearances on page 3/5.
■
A self-rimming countertop configuration is required for downdraft vent
installation. On installations with a downdraft vent, when sliding the
range into position, it will stop when the rear of the control panel or
side panels contact the notches toward the front of the countertop.
TOP VIEW - DOWNDRAFT ERV3015 WITH
SLIDE-IN, SELF-RIMMING INSTALLATION,
3” SIDE PANELS REMOVED
MIN. REQUIRED CABINET DEPTH: 26 3/8”
TOP VIEW - DOWNDRAFT ERV3015 WITH
SLIDE-IN, SELF-RIMMING INSTALLATION,
3” SIDE PANELS INSTALLED
CABINET DEPTHS 23 3/8” TO 26 3/8”
Cabinet Cutouts for Self-Rimming Installation (Models RNR30NIS and RNR30NIFS Only)
34 3/4”
(88.3 cm)
to
36 7/8”
(93.7 cm)
(see diagrams)
Countertop
1 5/8 (41.1 cm)
max. thickness
Rear wall or
countertop edge
countertop opening
29 1/4” (74.3 cm)
downdraft vent opening
27 1/2” (69.9 cm)
30 1/16” (76.2 cm)
cabinet opening
below countertop
below countertop
Cabinet face
Notch countertop
to width of cabinets
3/8” min. (1.0 cm)
countertop overhang
1” min. (2.6 cm)
to any combustibles
above counter both sides
20 3/8”
(51.8 cm)
to
23 3/8”
(59.4 cm)
20 3/8”
(51.8 cm)
2 5/8” (6.7 cm)
Countertop front
Max.
overhang
1 5/8”
(4.1 cm)
Rear wall or
countertop edge
countertop opening
29 1/4” (74.3 cm)
downdraft vent opening
27 1/2” (69.9 cm)
30 1/16” (76.2 cm)
2
cabinet opening
below countertop
below countertop
Cabinet face
Notch countertop
to width of cabinets
3/8” min. (1.0 cm)
countertop overhang
1” min. (2.6 cm)
to any combustibles
above counter both sides
23 3/8”
(59.4 cm)
2 5/8” (6.7 cm)
Countertop front
Max.
overhang
1 5/8”
(4.1 cm)