Viking VBCI5240GRSS Benutzung Und Pflege
5
Electronic Controls
Temperature Control Panel
The controller is located inside of the unit. The display will read OFF when the unit is off and will show temperature
when the unit is ON.
when the unit is ON.
IMPORTANT: The LED display is reading actual air temperature not product temperature. Under these conditions, an air
temperature swing does not change the actual product temperature. Product temperature remains at a very stable
temperature.
temperature swing does not change the actual product temperature. Product temperature remains at a very stable
temperature.
Product Temperature Set Points and Ranges
All Refrigerator
38°F
Range: 32°F to 39°F
Refrigerated Drawer
38°F
Range: 32°F to 39° F
Beverage Center
42°F
Range: 32°F to 48°F
Wine Center
55°F
Range: 44°F to 68° F
To view the SET point:
1. Press and release the SET button. The display will show the set point value.
2. Press and release the SET button or wait for 5 seconds to display the actual temperature again.
1. Press and release the SET button. The display will show the set point value.
2. Press and release the SET button or wait for 5 seconds to display the actual temperature again.
To change the SET point:
1. Press the SET button for 3 seconds to change the set point value.
2. The value of the set point will be displayed and the “°C” or “°F” LED will start blinking.
3. To change the set point value, press the UP or DOWN buttons within 10 seconds.
4. To store the new set point value, press the SET button again or wait 10 seconds.
1. Press the SET button for 3 seconds to change the set point value.
2. The value of the set point will be displayed and the “°C” or “°F” LED will start blinking.
3. To change the set point value, press the UP or DOWN buttons within 10 seconds.
4. To store the new set point value, press the SET button again or wait 10 seconds.
To lock the control:
1. Press the UP+DOWN buttons simultaneously for 3 seconds.
2. The “PoF” message will be displayed and the keyboard will be locked. At this point it will only be possible to see
1. Press the UP+DOWN buttons simultaneously for 3 seconds.
2. The “PoF” message will be displayed and the keyboard will be locked. At this point it will only be possible to see
the set point, the MAX or the MIN temperature stored.
3. If a button is pressed more than 3 seconds, the “PoF” message will be displayed.
To unlock the control:
1. Press the UP and DOWN buttons simultaneously for 3 seconds until the “Pon” message is displayed.
1. Press the UP and DOWN buttons simultaneously for 3 seconds until the “Pon” message is displayed.
To convert from Fahrenheit to Celsius:
1. Open door and hold F/C button for 3 seconds.
2. The unit will shut down briefly and then restart displaying the opposite temperature scale.
3. Repeat step 1 to convert back to original setting.
1. Open door and hold F/C button for 3 seconds.
2. The unit will shut down briefly and then restart displaying the opposite temperature scale.
3. Repeat step 1 to convert back to original setting.
Sabbath Mode
To activate SABBATH mode, open door and pres SAB button. If display lighting was activated, it will remain activated.
Turn off display lighting before initiating Sabbath Mode if display light will not be used.
Turn off display lighting before initiating Sabbath Mode if display light will not be used.
When in Sabbath mode:
• The display will be switched off (with the exclusion of the measurement temperature icon LED);
• The regulation will keep on working normally;
• The digital inputs will be deactivated (they will not work during SABBATH MODE);
• After any alarm condition the display will be switched on, coming back to the OFF mode at the end of the alarm
• The display will be switched off (with the exclusion of the measurement temperature icon LED);
• The regulation will keep on working normally;
• The digital inputs will be deactivated (they will not work during SABBATH MODE);
• After any alarm condition the display will be switched on, coming back to the OFF mode at the end of the alarm
condition;
• The keyboard will be deactivated with the exclusion of the SAB button.
To exit the SABBATH mode, open door and press SAB button. Close door. The display and light will turn on.