BlueStar BSPRT6010B Handbuch
10
B
URNER
O
PERATION
Push in and turn the control knob counter clockwise to HIGH to start the ignition process. The igniter will spark and make a
clicking sound. The clicking will stop after the burner ignites. The initial ignition process may take a few seconds. You may hear
multiple clicks before it ignites.
clicking sound. The clicking will stop after the burner ignites. The initial ignition process may take a few seconds. You may hear
multiple clicks before it ignites.
After ignition, turn the knob to your desired setting.
Turn
the knob to OFF to extinguish the burner. The flame may linger for several seconds until all the gas in the feeder tube is
burned off.
If the burner does not ignite, see the Before Calling for Service section for possible causes and solutions.
Burners have a re-ignite feature in case the flame is extinguished for any reason. It may take several seconds
for the burner to re-ignite.
for the burner to re-ignite.
Never operate the burner with the knob set between the HIGH and OFF position. The flame will NOT re-ignite
in this position and a gas leak could occur.
in this position and a gas leak could occur.
B
URNER
S
ETTINGS
Burners can be set to any setting between SIMMER and HIGH.
The flame should be adjusted to not wrap around the bottom edge of any pot or pan using the knob.
If the flame is set too high in relation to the edge of the pot or pan, you might scorch the backguard or other areas
around your rangetop
Do not leave empty non-stick pans on the French Top as the heat may damage the coating and the French Top
surface.
around your rangetop
Do not leave empty non-stick pans on the French Top as the heat may damage the coating and the French Top
surface.
At the HIGH setting, flames should appear as a defined cone with a dark blue center and light blue outside. Some yellow/orange
flame may be seen depending on the type of gas and the supply line.
flame may be seen depending on the type of gas and the supply line.
R
ING
G
RATES AND
T
OP
G
RATES
TIP: When placing the top grate back on the burner support, locate the sides with the raised edges and ensure they are positioned to
the left/right side of the burner. Insert the ring grate into the top grate by aligning the small notch in the top grate with the small
indents in the ring grate.
If the top grate is unsteady, remove both the top & ring grates, and adjust the four screws in the corners underneath the top grate
accordingly to even out the top grate.
Simmer Burner
The SIMMER burner gives you a choice of simmer settings from SIMMER to HIGH. The SIMMER setting can be used to gently melt
chocolate and hold delicate sauces at low temperatures.
the left/right side of the burner. Insert the ring grate into the top grate by aligning the small notch in the top grate with the small
indents in the ring grate.
If the top grate is unsteady, remove both the top & ring grates, and adjust the four screws in the corners underneath the top grate
accordingly to even out the top grate.
Simmer Burner
The SIMMER burner gives you a choice of simmer settings from SIMMER to HIGH. The SIMMER setting can be used to gently melt
chocolate and hold delicate sauces at low temperatures.
For the lowest simmer setting, push in and turn the knob to HIGH to ignite the burner, then turn counterclockwise to the
SIMMER setting on the knob.
SIMMER setting on the knob.
o For burners without the SIMMER setting marked on the control knob, push in and turn the control knob to HIGH to
initially ignite the burner, then turn the knob counterclockwise past the LOW indicator until the knob stops.
Your ring grates, top grates and burner heads may darken over time with use. This is normal.
TIP: To prevent your burners from darkening at an uneven rate, rotate the ring grate and top grates between more and less active
burners.
burners.
ATTENTION
CAUTION
ATTENTION
ATTENTION