Whirlpool WEG730H0D Benutzeranleitung
9
Electric igniters automatically light the surface burners when
control knobs are turned to IGNITE.
control knobs are turned to IGNITE.
Before setting a control knob, place filled cookware on the grate.
Do not operate a burner using empty cookware or without
cookware on the grate.
Do not operate a burner using empty cookware or without
cookware on the grate.
To Set:
1. Push in and turn knob counterclockwise to IGNITE.
All surface burners will click. Only the burner with the control
knob turned to IGNITE will produce a flame.
knob turned to IGNITE will produce a flame.
2. Turn knob to anywhere between HIGH and LOW.
Power Failure
In case of prolonged power failure, the surface burners can be lit
manually. Hold a lit match near a burner, and then turn knob
counterclockwise to IGNITE. After burner lights, turn knob to
setting.
manually. Hold a lit match near a burner, and then turn knob
counterclockwise to IGNITE. After burner lights, turn knob to
setting.
Surface Burners
IMPORTANT: Do not obstruct the flow of combustion and
ventilation air around the burner grate edges.
ventilation air around the burner grate edges.
Burner Cap: Always keep the burner cap in place when using a
surface burner. A clean burner cap will help avoid poor ignition and
uneven flames. Always clean the burner cap after a spillover, and
routinely remove and clean the caps according to the “General
Cleaning” section.
surface burner. A clean burner cap will help avoid poor ignition and
uneven flames. Always clean the burner cap after a spillover, and
routinely remove and clean the caps according to the “General
Cleaning” section.
Alignment: Be sure to align the gas tube opening in the burner
base with the orifice holder on the cooktop and the igniter
electrode with the notch in the burner base.
base with the orifice holder on the cooktop and the igniter
electrode with the notch in the burner base.
Gas Tube Opening: Gas must flow freely throughout the gas tube
opening for the burner to light properly. Keep this area free of soil,
and do not allow spills, food, cleaning agents or any other material
to enter the gas tube opening. Keep spillovers out of the gas tube
opening by always using a burner cap.
opening for the burner to light properly. Keep this area free of soil,
and do not allow spills, food, cleaning agents or any other material
to enter the gas tube opening. Keep spillovers out of the gas tube
opening by always using a burner cap.
Burner Ports: Check burner flames occasionally for proper size
and shape as shown in the previous illustration. A good flame is
blue in color, not yellow. Keep this area free of soil, and do not
allow spills, food, cleaning agents or any other material to enter the
burner ports.
and shape as shown in the previous illustration. A good flame is
blue in color, not yellow. Keep this area free of soil, and do not
allow spills, food, cleaning agents or any other material to enter the
burner ports.
To Clean:
IMPORTANT: Before cleaning, make sure all controls are off and
the cooktop is cool. Do not use oven cleaners, bleach or rust
removers. Do not wash in the dishwasher.
the cooktop is cool. Do not use oven cleaners, bleach or rust
removers. Do not wash in the dishwasher.
1. Remove the burner cap and the burner base and clean
according to “General Cleaning” section.
2. Clean the gas tube opening with a damp cloth.
3. Clean clogged burner ports with a straight pin as shown. Do
not enlarge or distort the port. Do not use a wooden toothpick.
If the burner needs to be adjusted, contact a trained repair
specialist.
If the burner needs to be adjusted, contact a trained repair
specialist.
COOKTOP
WARNING
Fire Hazard
Do not let the burner flame extend beyond the edge of
the pan.
the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death
or fire.
or fire.
REMEMBER: When range is in use, the entire cooktop area
may become hot.
may become hot.
A. Burner cap
B. Gas tube opening
B. Gas tube opening
C. Burner base
D. Igniter electrode
E. Orifice holder
A. 1 to 1
¹⁄₂
" (2.5 to 3.8 cm)
B. Burner ports
A
B
C
D
E
B
A