Maytag MHW8100DC Benutzeranleitung

First try the solutions suggested here or visit our website at www.maytag.com/product_help –

In Canada www.maytag.ca for assistance and to possibly avoid a service call.  

“Sud” (Excess suds)  

appears in display

Excessive suds in washer. Washer is 

running a suds reduction routine. 

Allow the washer to continue. Use only HE detergent.  

Always measure detergent, and base detergent quantity on  

load size. Follow detergent manufacturer’s instructions. 

Check for proper water supply.

Both hoses must be attached and have water flowing to the inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.

F09 followed by E01  

(drain pump system  

error) appears in display

Check plumbing for correct drain hose 

installation. Drain hose extends into  

standpipe farther than 4

1

⁄

2

" (114 mm). 

Check drain hose for proper installation. 
Make sure the drain hose is not kinked, pinched, or blocked. 
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above the floor.

F05 

followed by 

E02 

 

(door will not lock)  

appears in display

Washer door not locking.

Touch POWER/CANCEL to cancel the cycle. Make sure the door is 

closed completely and latching. Check for items in the washer drum 

that may be keeping the door from closing completely.

Washer beeps when 

START is touched 

Door not closed.

Close the door completely.

“rL” (remove load)  

appears in display

Load detected in drum during Clean 

Washer with affresh

®

 cycle.

Remove items from washer drum and restart Clean Washer with  

affresh

®

 cycle.

Washer making error 

beeps  

Door has not been opened and closed 

for at least 3 cycles.

This code may appear when the washer is first turned on.  

Open and close the door to clear the display.

Once any possible issues are corrected, touch POWER/CANCEL once to clear the code. Reselect and restart the cycle.

F## E##

 code other  

than as described above 

appears in display

System error code.

Touch POWER/CANCEL once to clear the code. Then touch 

POWER/CANCEL again to restart washer. If code appears again, 

call for service.

Not using HE detergent or using too 

much HE detergent.

Use only HE detergent. Always measure detergent and follow 

manufacturer’s directions based on load size and soil level. 

“dEt” (Detergent)  

appears in display

The dispenser cartridge is not  

detected.

Ensure the dispenser cartridge is inserted correctly and the 

dispenser drawer is shut completely. For single-load doses of 

detergent, ignore this message.

The three detergent level 

status lights are lit 

Detergent dispenser is not securely in 

place.

Pull out the dispenser and slide it back in place.

Detergent Level sensor error.

Touch POWER/CANCEL to reset system. If this fails, unplug 

washer or disconnect power for one minute, then plug in washer or 

reconnect power. 

“Int” (interrupted)  

appears in display

The cycle was paused or cancelled. 

The washer can take 20 to 30 minutes to stop spinning  

and drain and will display this error code during that time.  

Touch POWER/CANCEL once to clear the code. Then touch 

POWER/CANCEL again to restart washer. 

Clean Washer LED  

flashing at end of wash 

cycle

The washer has run 30 wash cycles and 

is indicating a reminder to run the Clean 

Washer with affresh

® 

cycle.

Run the Clean Washer with affresh

® 

cycle. If the Clean Washer 

with affresh

® 

cycle is not turned on, the LED will stop flashing at 

the end of a wash cycle after running 3 more regular wash cycles. 

After 30 more wash cycles are completed, the Clean Washer LED 

will again flash at the end of a wash cycle as a reminder.

Lo followed by FL or F8 

followed by E1 (water 

supply error) appears in 

display

Unit will drain for 8 minutes while door remains locked. When  

complete, touch POWER/CANCEL once to clear the code. Then 

touch POWER/CANCEL again to restart washer. If code appears 

again, call for service. 

Touch WATER HARDNESS to change water hardness to “soft.”

If used, auto shut off connectors and hoses must be properly in-

stalled and in working order.