Best CP57IQT662SB Installationsanweisungen
5
1. INSTALL DUCTWORK AND ELECTRICAL WIRING
1.1 N
ON
-D
UCTED
I
NSTALLATION
(CP55IQ S
ERIES
POWER
PACKS
ONLY
)
CP55IQ Series power packs may be non-ducted. ANKCP55 non-duct kit must be installed (sold separately).
1.2 D
UCTED
I
NSTALLATION
(A
LL
POWER
PACKS
)
For a CP57E Series power pack, either an exterior blower or in-line blower must be used. The CP57E Series power pack must be
installed with blower models ILB3, ILB6, ILB9, ILB11, EB6, EB9, EB12 or EB15 only. Other blowers cannot be substituted (blowers
sold separately.) Plan where and how the ductwork will be installed.
installed with blower models ILB3, ILB6, ILB9, ILB11, EB6, EB9, EB12 or EB15 only. Other blowers cannot be substituted (blowers
sold separately.) Plan where and how the ductwork will be installed.
If installing exterior or in-line blower, refer to instructions packed with blower and follow steps 1 up to 7, 11, 13 and up of
this manual.
this manual.
Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. If installing CP55IQ Series power
pack, use 8” round ductwork and if installing CP57IQT or CP57E Series power pack, use 10” round ductwork. Use metal foil duct
tape to seal duct joints.
pack, use 8” round ductwork and if installing CP57IQT or CP57E Series power pack, use 10” round ductwork. Use metal foil duct
tape to seal duct joints.
NOTE: It is recommended that there be a minimum of 6" of straight duct from the hood to an elbow for 8" duct and 12" for 10" duct.
1.3 A
LL
I
NSTALLATIONS
The minimum power pack distance above cooktop must not be less than 24’’. A maximum of 30” above cooktop is
recommended for best capture of cooking impurities.
recommended for best capture of cooking impurities.
Distances over 30” are at the installer and users discretion.
Run 3-wire power supply cable to installation location. Its length should extend at least 4 feet below the bottom of the custom hood.
HH0201A
POWER PACK
ROOF CAP
WALL
CAP
CAP
8” ROUND DUCT FOR CP55IQ OR
10” ROUND DUCT FOR CP57IQT
10” ROUND DUCT FOR CP57IQT
8” ROUND ADAPTER & DAMPER
FOR CP55IQ OR
10” ROUND ADAPTER FOR CP57IQT
FOR CP55IQ OR
10” ROUND ADAPTER FOR CP57IQT
24” TO 30”
ABOVE COOKING SURFACE
ABOVE COOKING SURFACE
8” ROUND ELBOW FOR CP55IQ OR
10” ROUND ELBOW FOR CP57IQT
10” ROUND ELBOW FOR CP57IQT
10” IN LINE
VERTICAL DAMPER FOR CP57IQT
VERTICAL DAMPER FOR CP57IQT
IN-LINE BLOWER
10” ROUND DUCT
(except ILB3, 8’’ ROUND DUCT)
HH0114A
24” TO 30” ABOVE
COOKING SURFACE
ROOF CAP
WALL
CAP
CAP
POWER PACK
HH0115A
POWER PACK
EXTERIOR BLOWER
10” ROUND DUCT
24” TO 30”
ABOVE
COOKING SURFACE
ABOVE
COOKING SURFACE
10” ROUND ELBOW
EXTERIOR
BLOWER
CP55IQ (
SINGLE
INTERNAL
BLOWER
)
OR
CP57IQT (
DUAL
INTERNAL
BLOWER
)
T
YPICAL
D
UCTWORK
CP57E
WITH
M
ODEL
ILB3, ILB6, ILB9
OR
ILB11 I
N
-
LINE
B
LOWER
T
YPICAL
D
UCTWORK
(
BLOWER
LOCATION
IS
SHOWN
FOR
REFERENCE
ONLY
)
CP57E E
XTERIOR
B
LOWER
T
YPICAL
D
UCTWORK