Dacor DR30EIFS Installationsanweisungen

Product Specifications

IMPORTANT: Observe all governing codes and ordinances 

during planning and installation. Contact your local building 

department for further information.

Electrical Requirements 

(All models 

except those ending with -C)

It is the owner’s responsibility to ensure that a licensed electrician 

performs the installation of the electrical supply for this appliance. 

The electrical installation, including minimum supply wire size, 

must comply with the National Electric Code ANSI/NFPA 70 (latest 

revision) and local codes and ordinances.

 A copy of this standard 

may be obtained from: 

National Fire Protection Association 

1 Batterymarch Park 

Quincy, Massachusetts 02269-9101

The correct voltage, frequency and amperage must be supplied 

to the appliance from a dedicated, grounded, single phase circuit 

that is protected by a properly sized circuit breaker or time-delay 

fuse. If a time-delay fuse is utilized, fuse both sides of the line (L1 

and L2).

240 Vac 60 Hz, 4-wire*, 50 Amp.

11.94 kW (49.75 Amp.)

* Two 120 Vac hot (L1 and L2), one neutral (N1) and one ground.
The above electrical specifications are for reference only. See 

the range data label for exact specifications. See inside cover for 

location.
•

The wiring needs to be long enough to allow the range to be 

pulled out for service, while remaining connected.

•

The wiring connected to the range must:
◊  Meet NEMA standards and have a minimum rating of 

250 Volts @ 50 Amp.

◊  Include a strain relief
◊  Be terminated by tinned leads, closed loop terminals or 

open ended spade lugs with upturned ends

◊  Connect to a junction box or receptacle installed by a 

licensed electrician

The appliance may be connected one of the following ways:
•

Using conduit: 
◊  A 4-wire conduit connected to a 4-wire junction box, or
◊  A 3-wire conduit (where local code permits) connected to 

a  3-wire junction box.

Suggested conduit wiring color code: black, white, red 

and green.

•

Using an appliance cord:
◊  A 4-wire appliance cord equipped with a NEMA 14-50P 

plug connected to a NEMA 14-50R receptacle, or

◊  A 3-wire appliance cord (where local code permits) 

equipped with a NEMA 10-50P plug connected to a 

NEMA 10-50R receptacle

Appliance cord plug must be UL listed type SRD or SRDT.

Electrical Requirements 

(Models 

DR30ES-C and DR30EFS-C)

•

Models DR30ES-C and DR30EFS-C are freestanding ranges 

that come with a factory installed 4-wire appliance cord and 

NEMA 14-50P plug. This wiring configuration is required 

for freestanding ranges installed in Canada, although they 

may be used elsewhere, if local codes permit. The plug 

is designed to plug directly into a NEMA 14-50R electrical 

receptacle installed by a licensed electrician according to 

the specifications below. Do not modify the factory wiring on 

models with -C at the end of the model number. 

•

It is the owner’s responsibility to ensure that the required 

4-wire electrical outlet compatible with the power cord is 

installed by a licensed electrician as specified below prior to 

range installation. The electrical outlet installation, including 

minimum supply wire size and grounding, must be in 

accordance with all governing codes and ordinances. 

•

The correct voltage, frequency and amperage must be 

supplied to the appliance from a separate, grounded, circuit 

that is protected by a properly sized circuit breaker or time 

delay fuse. If a fuse is utilized, fuse both sides of the line (L1 

and L2). Refer to the ratings on the range rating label.

240 Vac 60 Hz, 4-wire*, 50 Amp.

11.94 kW (49.75 Amp.)

* Two 120 Vac hot (L1 and L2), one neutral (N1) and one ground.
The ratings above are for reference only - refer to the range rating 

label (see inside cover).