Fisher & Paykel DD36SS Installationsanleitung
3
SAFETY PRACTICES & PRECAUTIONS
WARNING:
ALL WALL AND FLOOR OPENINGS WHERE THE Downdraft IS INSTALLED MUST
BE SEALED.
Consult the cooktop installation instructions given by the manufacturer before making any cutouts.
MOBILE HOME INSTALLATION - The installation of this Downdraft must conform to the Manufactured
Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard for
Mobile Home Construction and Safety, Title 24, HUD, Part 280). Four wire power supply must be used
and the appliance wiring must be revised. See Electrical Requirements (page 4).
MOBILE HOME INSTALLATION - The installation of this Downdraft must conform to the Manufactured
Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard for
Mobile Home Construction and Safety, Title 24, HUD, Part 280). Four wire power supply must be used
and the appliance wiring must be revised. See Electrical Requirements (page 4).
Venting system MUST terminate outside the home.
DO NOT terminate the ductwork in an attic or other enclosed space.
DO NOT use 4" laundry-type wall caps.
Flexible-type ductwork is not recommended.
DO NOT obstruct the flow of combustion and ventilation air.
Failure to follow venting requirements may result in a fire.
Electrical ground is required on this downdraft ventilation system.
If cold water pipe is interrupted by plastic, non-metallic gaskets or other materials, DO NOT use
for grounding.
for grounding.
DO NOT ground to a gas pipe.
DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding
circuit could result in electrical shock.
circuit could result in electrical shock.
Check with a qualified electrician if you are in doubt as to whether the downdraft is properly
grounded.
grounded.
Failure to follow electrical requirements may result in a fire.
WARNING
:
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
Use this unit only in the manner intended by the manufacturer. If you have
any questions, contact the manufacturer. Before servicing or cleaning unit,
switch power off at service panel and lock the service disconnecting means
to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel. Installation Work And Electrical
Wiring Must Be Done By Qualified Person(s) In Accordance With All
Applicable Codes And Standards, Including Fire-Rated Construction.
Sufficient air is needed for proper combustion and exhausting of gases from
fuel burning equipment through the flue (chimney) to prevent backdrafting.
Follow the heating equipment manufacturer's guideline and safety
standards such as those published by the National Fire Protection
Association (NFPA), and the American Society for Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), and the local code authorities. When
cutting or drilling into wall or ceiling, do not damage electrical wiring and
other hidden utilities. Ducted fans must always be vented to the outdoors.
any questions, contact the manufacturer. Before servicing or cleaning unit,
switch power off at service panel and lock the service disconnecting means
to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel. Installation Work And Electrical
Wiring Must Be Done By Qualified Person(s) In Accordance With All
Applicable Codes And Standards, Including Fire-Rated Construction.
Sufficient air is needed for proper combustion and exhausting of gases from
fuel burning equipment through the flue (chimney) to prevent backdrafting.
Follow the heating equipment manufacturer's guideline and safety
standards such as those published by the National Fire Protection
Association (NFPA), and the American Society for Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), and the local code authorities. When
cutting or drilling into wall or ceiling, do not damage electrical wiring and
other hidden utilities. Ducted fans must always be vented to the outdoors.