Electrolux EIMGD60JIW Bedienungsanleitung
NOTE TO
INSTALLER
Leave these instructions
with the customer.
with the customer.
REMARQUE POUR
L’INSTALLATEUR
Laissez ces instructions au
client.
client.
Suite de la version française au verso.
NOTA AL
INSTALADOR
Deje estas instrucciones
con en cliente.
con en cliente.
Español continua en la pagina trasera.
WARNING
Dryer must be properly grounded at all times.
•
Vent dryer through free-fl owing, outdoor-vented, metal duct system.
•
Improper gas installation or LP conversion could result in injury or even death.
•
Avoid back or other injury. Use more than one person to move, tip or lift the dryer.
•
IMPORTANT
Please read all safety instructions before using your
new front-loading dryer. For best drying results with
your new dryer, remember to review:
new front-loading dryer. For best drying results with
your new dryer, remember to review:
9 INSTALLATION INSTRUCTIONS
9 USE & CARE GUIDE
9 USE & CARE GUIDE
137269500A (0911)
For toll-free telephone support in the U.S. and Canada:
1-877-4ELECTROLUX
1-877-4ELECTROLUX
(1-877-435-3287).
For online support and product information,
visit
visit
http://www.electroluxappliances.com.
Para obtener asistencia telefónica gratuita en los Estados Unidos y Canadá:
1-877-4ELECTROLUX
1-877-4ELECTROLUX
(1-877-435-3287).
Para obtener asistencia e información en Internet sobre el producto,
visite
visite
http://www.electroluxappliances.com.
Pour rejoindre le service sans frais aux États-Unis et au Canada:
1-877-4ELECTROLUX
1-877-4ELECTROLUX
(1-877-435-3287).
Pour obtenir de l’aide et de l’information sur les produits en ligne,
visitez le site http://www.electroluxappliances.com.
CLEAN LINT FILTER AFTER
EVERY LOAD.
EVERY LOAD.
NETTOYEZ LE FILTRE À
CHARPIE APRÈS CHAQUE
SÉCHAGE.
CHARPIE APRÈS CHAQUE
SÉCHAGE.
LIMPIE EL FILTRO DE
PELUSAS DESPUÉS DE
CADA CARGA.
PELUSAS DESPUÉS DE
CADA CARGA.
EMPTY DRUM
CONTENTS
CONTENTS
CART FROM REAR
ONLY WITH 7" MIN.
CART FORKS
ONLY WITH 7" MIN.
CART FORKS
DO NOT CART
FROM FRONT
FROM FRONT
DO NOT USE KNEE IN CABINET
SIDE TO MOVE UNIT
SIDE TO MOVE UNIT
DO NOT CART
FROM SIDE
FROM SIDE
DO NOT USE OPEN DOOR
TO LIFT OR TIP THE UNIT
TO LIFT OR TIP THE UNIT
2-PERSON CARRYING
STRAPS, FRONT-TO-
BACK RECOMMENDED
STRAPS, FRONT-TO-
BACK RECOMMENDED
CAREFULLY TIP
REMOVE & SAVE
PROTECT FLOOR
RETURN
UPRIGHT
UPRIGHT
A)
B)
C)
D)
UNPACKING & HANDLING
IMPORTANT
For pedestal, stacked or closet installations, see
detailed installation instructions enclosed.
detailed installation instructions enclosed.
USE ONLY 4 INCH (10.2 CM) RIGID METAL OR SEMI-RIGID
•
METAL DUCTING
REPLACE PLASTIC OR FOIL DUCTS WITH METAL
•
CLEAN LINT FROM PRESENT DUCT SYSTEM BEFORE
•
ADDING ON
SEE CHART TO THE RIGHT FOR ACCEPTABLE NUMBER OF
•
90° TURNS IN SYSTEM
DO NOT USE SCREWS TO CONNECT DUCTS
•
DO NOT USE REGULAR DUCT TAPE TO CONNECT DUCTS, ONLY
•
METAL FOIL TAPE
4" (10.2 cm) CLAMP RECOMMENDED FOR CONNECTION
•
BETWEEN DRYER & EXHAUST SYSTEM
EXHAUST SYSTEM MUST BE VENTED OUTSIDE WITH
•
APPROVED VENT HOOD
TO VENT LEFT OR RIGHT FROM DRYER, USE 90° QUICK-
•
TURN ELBOW
FOR INSTALLATION IN A RECESSED AREA OR CLOSET, SEE
•
COMPLETE INSTALLATION INSTRUCTIONS
FOR MOBILE HOME INSTALLATION, SEE COMPLETE
•
INSTALLATION INSTRUCTIONS
Number of 90° tur
ns
MAXIMUM LENGTH
of 4” (10.2cm) Rigid Metal Duct
VENT HOOD TYPE
(Preferred)
4”
(10.2cm)
louvered
2.5”
(6.35cm)
0
125 ft. (38.0m)
110 ft. (33.5m)
1
115 ft. (35.0m)
100 ft. (30.5m)
2
105 ft. (32.0m)
90 ft. (27.5m)
3
95 ft. (29.0m)
80 ft. (24.5m)
4
85 ft. (26.0m)
70 ft. (21.5m)
*Do not install plastic or foil ducting. If installing semi-rigid
ducting, do not exceed 8 ft (2.4 m) total duct length.
ducting, do not exceed 8 ft (2.4 m) total duct length.
INCORRECT
CORRECT
USE ONLY 4 INCH (10 2 CM
VENT EXHAUST
ADJUST
LEVEL BOTH WAYS
CONNECT POWER
OPEN GAS VALVE AND
CHECK FOR LEAKS
WITH SOAPY WATER
CHECK FOR LEAKS
WITH SOAPY WATER
CHECK STABILITY,
CORNER-TO-CORNER
CORNER-TO-CORNER
raise
lower
B)
C)
D)
E)
A)
CAUTION
ELECTRICAL SHOCK HAZARD
Do NOT use prong adapter.
Do NOT remove ground prong.
Do NOT use extension cord.
Do NOT use prong adapter.
Do NOT remove ground prong.
Do NOT use extension cord.
LEVEL & CONNECT
30 AMP
30 AMP
DON'T MOVE
MOVE GROUND
GREEN
RED OR
BLACK
BLACK
RED OR
BLACK
BLACK
WHITE
INSTALL
U.L.-APPROVED
STRAIN RELIEF
APPLY APPROVED THREAD
SEALANT.
REFER TO INSTALLATION
INSTRUCTIONS FOR MORE
DETAILED INFORMATION.
SEALANT.
REFER TO INSTALLATION
INSTRUCTIONS FOR MORE
DETAILED INFORMATION.
GAS DRYER
ELECTRIC DRYER
WRENCH-TIGHT
MANUAL
SHUTOFF
L.P. SYSTEMS MUST USE
COVERSION KIT INSTALLED
BY QUALIFIED TECHNICIAN.
COVERSION KIT INSTALLED
BY QUALIFIED TECHNICIAN.
GAS DRYER
HEAT SOURCE
TURN OFF WATER SUPPLY
TO WASHER.
TO WASHER.
INSPECT RUBBER
WASHER. REPLACE
IF WORN.
WASHER. REPLACE
IF WORN.
REMOVE COLD WATER HOSE
FROM COLD WATER SUPPLY.
FROM COLD WATER SUPPLY.
COLD WATER
SUPPLY HOSE
TO WASHER.
SUPPLY HOSE
TO WASHER.
CONNECT "Y" FIXTURE OR
EXTENSION HOSE TO COLD
SUPPLY. TIGHTEN BY HAND.
EXTENSION HOSE TO COLD
SUPPLY. TIGHTEN BY HAND.
TIGHTEN ADDITIONAL
2/3 TURN WITH PLIERS.
2/3 TURN WITH PLIERS.
TURN ON WATER AND
CHECK FOR LEAKS.
CHECK FOR LEAKS.
RUN WATER FROM
COLD OUTLET TO
CLEAR CONTAMINANTS.
COLD OUTLET TO
CLEAR CONTAMINANTS.
WATER INLET
ON DRYER.
ON DRYER.
USE HOSE EXTENSION IF
"Y" CONNECTOR CANNOT
ATTACH DIRECTLY TO
COLD WATER SUPPLY.
"Y" CONNECTOR CANNOT
ATTACH DIRECTLY TO
COLD WATER SUPPLY.
TIGHTEN ALL CONNECTIONS BY
HAND. TIGHTEN ADDITIONAL 2/3
TURN WITH PLIERS.
HAND. TIGHTEN ADDITIONAL 2/3
TURN WITH PLIERS.
REMOVE FROM BAG. INSPECT
FOR RUBBER WASHERS.
FOR RUBBER WASHERS.
B)
C)
D)
E)
G)
H)
I)
F)
A)
IF THIS IS NOT A STEAM DRYER, SKIP TO STEP 5.
CONNECT WATER
Perform brief installation cycle for your model as follows:
If dryer has this console:
Empty dryer drum and close door.
1.
Wake dryer up (any button), rotate cycle knob to
2.
touch
up, press start then cancel.
Wake dryer up again, immediately and simultaneously
3.
press and hold sanitize and my favorite buttons for 5
seconds.
seconds.
LCD will display
4.
INSTAL CYCLE
and show estimated
time of cycle completion. Press start.
Installation Cycle will perform various diagnostic routines.
5.
At cycle completion, LCD will display
6.
INSTAL PASS!
or
prompt an action during cycle such as
SERVICE CORD
,
NO GAS
or
CALL SERVICE 877 435 3287
.
Dryer will exit the Installation Cycle and return to normal op-
7.
eration next time you wake it up. Read Use and Care Guide
and enjoy your new premium dryer!
and enjoy your new premium dryer!
If dryer has this console:
Empty washer drum and close door.
1.
Wake up the dryer by pressing any button and then
2.
follow the prompts on the LCD User Interface, including
language selection. NOTE: this initial, automatic cycle
can be manually accessed through the scroll buttons in
the set prefs sections under options.
language selection. NOTE: this initial, automatic cycle
can be manually accessed through the scroll buttons in
the set prefs sections under options.
LCD will display
3.
INSTAL CYCLE
and show estimated
time of cycle completion. Press start.
Installation Cycle will perform various diagnostic routines.
4.
At cycle completion, LCD will display
5.
INSTAL PASS!
or
prompt an action during cycle such as
SERVICE CORD
,
NO GAS
or
CALL SERVICE 877 435 3287
.
Dryer will exit the Installation Cycle and return to normal op-
6.
eration next time you wake it up. Read Use and Care Guide
and enjoy your new premium dryer!
and enjoy your new premium dryer!
OPERATE