Fisher & Paykel RF135BDRX4 Installationsanleitung
Refrigerator Surround Kit
Installation instructions
E402B, E442B, E522B, RF610A, RF540, RF522A models
NZ AU GB AE HK SG IE US CA EU CN IN
Important!
SAVE THESE INSTRUCTIONS
The model shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website
www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
3
Parts suPPlied
Top trim (x 1)
Side trim (x 2)
Bottom trim
(x 1)
Side trim
brackets (x 10)
or
Side trim
brackets (x 4)
Side trim centre
brackets (x 6)
Top trim brackets:
– Single
refrigerator kits
(2 x brackets)
– Side by Side kits
(3 x brackets)
Screw type A:
#8 x 12 Pozi
Drive CSK (x 26)
Long screws
10 x 75 CSK PH
P/no SP0207
(x 2)
Floor stops
P/no 460912
(x 2)
Washers
4 x 11 x 1mm
(x 2)
6
seCure side
trim braCkets
Locate the ten side trim brackets.
Position five brackets to the left hand side of
the cabinet and the remaining five brackets to
the right hand side of the cabinet.
Brackets should be evenly spaced down each
side (see diagram 3a/b). Secure each of these
brackets with the two screws provided.
Care must be taken to line up the front edge
of the brackets with the leading edges of
the cabinet.
Position five brackets to the left hand side of
the cabinet and the remaining five brackets to
the right hand side of the cabinet.
Brackets should be evenly spaced down each
side (see diagram 3a/b). Secure each of these
brackets with the two screws provided.
Care must be taken to line up the front edge
of the brackets with the leading edges of
the cabinet.
Diagram 3b
Diagram 3a
or
7
seCure Floor stoPs
Two floor stops are supplied to prevent the refrigerator from being pushed too far back into the cavity.
These are mounted on the base or floor at a distances of 688mm (27") from the face front edge of the
trim kit.
These are mounted on the base or floor at a distances of 688mm (27") from the face front edge of the
trim kit.
688 mm
150 mm
Diagram 4
4
Cabinetry dimensions
A
B
D
A
B
D
Diagram 1a
Cabinet at floor level
Diagram 1b
Cabinet above toe kick
E
E
C1
C2
Installation diagrams for illustration purposes only
Diagram 1
Cutout dimensions – flush to edge of door
(mm / inches)
635 (25") model
680 (26
3/4
") model
790 (31
1/8
") model
900 (35
7/16
") model
635 (25") model
+ 635 (25") model
680 (26
3/4
") model
+ 680 (26
3/4
") model
790 (31
1/8
") model
+ 790 (31
1/8
") model
A
width
807 (31 13⁄16”)
852 (33 9⁄16”)
962 (37 7⁄8”)
1072 (42 1⁄4”)
1467 (57 3⁄4”) 1557 (61 5⁄16”)
1777 (70”)
B
depth*
700 (27 9⁄16”)
700 (27 9⁄16”)
700 (27 9⁄16”)
700 (27 9⁄16”)
700 (27 9⁄16”)
700 (27 9⁄16”)
700 (27 9⁄16”)
C1
height**
1790 (70 1/2") 1790 (70 1/2") 1790 (70 1/2") 1875 (73 13⁄16") 1790 (70 1/2") 1790 (70 1/2") 1790 (70 1/2")
C2
height***
1806 (71 1/8") 1806 (71 1/8") 1806 (71 1/8") 1891 (74 1/2") 1806 (71 1/8") 1806 (71 1/8") 1806 (71 1/8")
D
air vent
depth
depth
200 (8”)
200 (8”)
200 (8”)
200 (8”)
200 (8”)
200 (8”)
200 (8”)
E
air vent
width
width
502 (19 13/16") 547 (21 9⁄16")
657 (25 7/8")
767 (30 1/4")
1162 (45 3⁄4") 1252 (49 5⁄16")
1472 (58")
* Depth is a minimum requirement
** Height is without 16mm MDF packer
*** Height is with 16mm MDF packer
** Height is without 16mm MDF packer
*** Height is with 16mm MDF packer
Cut out dimensions above are to be used as minimum dimensions.
5
seCure toP
trim braCkets
Locate the two/three top trim brackets.
For the Side By Side Refrigerator kits, one
bracket is to be screwed in the top centre of the
cabinet, secure the top bracket with two of the
screws (Type A, #8 x 12 Pozi Drive CSK).
For all other kits, the two brackets are to be
secured on either side, by two screws which are
mounted from the side (see diagram 2).
Looking at the front of the product, place the
top brackets on top of the wooden cabinet.
Care must be taken to line up the top front
edge of the brackets with the leading edge of
the cabinet.
Hint: Holes should be drilled in the centre of
the slot in the brackets to allow for adjustment.
For the Side By Side Refrigerator kits, one
bracket is to be screwed in the top centre of the
cabinet, secure the top bracket with two of the
screws (Type A, #8 x 12 Pozi Drive CSK).
For all other kits, the two brackets are to be
secured on either side, by two screws which are
mounted from the side (see diagram 2).
Looking at the front of the product, place the
top brackets on top of the wooden cabinet.
Care must be taken to line up the top front
edge of the brackets with the leading edge of
the cabinet.
Hint: Holes should be drilled in the centre of
the slot in the brackets to allow for adjustment.
End bracket
Centre bracket
Diagram 2
1
reFrigerator surround kit
This kit is designed to be used with models with a cabinet height of
between: 1695mm – 1806mm (66 ¾” – 71 1/8”) with curved or flat door styling.
You can find the part number for each installation type in Section 10.
between: 1695mm – 1806mm (66 ¾” – 71 1/8”) with curved or flat door styling.
You can find the part number for each installation type in Section 10.
To give the most integrated look, the kitchen cabinetry should be flush with
the front of the refrigerator door.
the front of the refrigerator door.
Tools required (not included)
■
■
No. 2 drill bit – long
■
■
Electric drill
■
■
Phillips screwdriver
■
■
1 x 16mm (5⁄8 inch) piece of MDF the same size as the base of the cavity
(optional). Not needed if refrigerator cabinet is sitting directly on the floor
and not on raised toe kick area
(optional). Not needed if refrigerator cabinet is sitting directly on the floor
and not on raised toe kick area
■
■
Joiner kit (part number 819264) required if joining two refrigerators side by side
Before starting
All dimensions are internal or cut out dimensions.
The refrigerator can be installed:
1. In a cavity with a toe kick under the product with the bottom trim fitted to the base (diagram 1b/5).
2. In a cavity with 16mm panel under the product with the bottom trim fitted to the panel
(diagram 1a/6).
3. In a cavity where the product is at floor level with no bottom trim (diagram 1a).
4. Check whether your fridge has hinges concealed by the front of the fridge door. If unsure refer to
page 2 note*** for instructions.
The refrigerator can be installed:
1. In a cavity with a toe kick under the product with the bottom trim fitted to the base (diagram 1b/5).
2. In a cavity with 16mm panel under the product with the bottom trim fitted to the panel
(diagram 1a/6).
3. In a cavity where the product is at floor level with no bottom trim (diagram 1a).
4. Check whether your fridge has hinges concealed by the front of the fridge door. If unsure refer to
page 2 note*** for instructions.
2
getting started
1
Check that the internal Cupboard Cavity dimensions are correct (see diagram 1a/b).
2
Unpack the refrigerator and/or freezer cabinets from their separate delivery cartons (see individual
cartons for unpacking procedures).
3
Ensure the floor and/or the cupboards are protected from damage during the unpacking and
assembly of the cabinets.
4
Check the refrigerator and freezer doors are hinged on the desired side.
5
Check that the kit is complete (refer to Parts Supplied in section 3).
Note 1: Due to the size of the refrigerator cabinets, it is essential that assembly of the kit be undertaken
with a minimum of two able-bodied persons.
Note 2: It is important to include adequate venting to the top of the cabinet to ensure the efficient
operation of the refrigerator.
Note 3: The installation of the cabinet or cabinets can be at floor level as shown in diagram 1a or installed
above the toe kick board as in diagram 1b.
Note 4: Rollers and feet must be fitted.
Note 5: Cabinets installed above the toe kit should have a floor base constructed to support the total
weight of the loaded cabinet or cabinets placed on it.
with a minimum of two able-bodied persons.
Note 2: It is important to include adequate venting to the top of the cabinet to ensure the efficient
operation of the refrigerator.
Note 3: The installation of the cabinet or cabinets can be at floor level as shown in diagram 1a or installed
above the toe kick board as in diagram 1b.
Note 4: Rollers and feet must be fitted.
Note 5: Cabinets installed above the toe kit should have a floor base constructed to support the total
weight of the loaded cabinet or cabinets placed on it.
The placement of the 16mm (5/8") MDF or plywood under the cabinet or cabinets on either installation
type is to allow the fitment of the bottom trim that covers it. It is optional.
type is to allow the fitment of the bottom trim that covers it. It is optional.