Sub-Zero IC24RLH Installationsanweisungen
subzero.com
|
5
SITE PREPARATION
Electrical
Installation must comply with all applicable electrical codes.
The electrical supply must be located within the shaded
area shown in the illustration and chart below. A separate
circuit, servicing only this appliance is required. A ground
fault circuit interrupter (GFCI) is not recommended and may
cause interruption of operation.
area shown in the illustration and chart below. A separate
circuit, servicing only this appliance is required. A ground
fault circuit interrupter (GFCI) is not recommended and may
cause interruption of operation.
The electrical outlet must be positioned with the grounding
prong to the right of the thinner blades.
prong to the right of the thinner blades.
CAUTION
The outlet must be checked by a qualified electrician to
be sure that it is wired with the correct polarity. Verify
that the outlet is properly grounded.
be sure that it is wired with the correct polarity. Verify
that the outlet is properly grounded.
WARNING
Do not use an extension cord, two-prong adapter or
remove the power cord ground prong.
remove the power cord ground prong.
ELECTRICAL REQUIREMENTS
Electrical Supply
115 VAC, 60 Hz
Service
15 amp
Receptacle
3-prong grounding-type
ELECTRICAL SUPPLY LOCATION
WIDTH
A
18" Models
6"
(152)
24" Models
9
1
/
2
"
(241)
27" Models
11"
(279)
30" Models
12
1
/
2
"
(318)
36" Models
15
1
/
2
"
(394)
Plumbing
Installation must comply with all applicable plumbing codes.
The water supply line should be located within the shaded
area shown in the illustration below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self-piercing valves.
The water supply line must be flush to the floor and not
interfere with installation of the anti-tip bracket.
area shown in the illustration below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self-piercing valves.
The water supply line must be flush to the floor and not
interfere with installation of the anti-tip bracket.
Column and tall models with an ice maker or water dis-
penser feature a water filtration system. An in-line filter is
required for drawer models with an ice maker when water
conditions have a high sediment content.
penser feature a water filtration system. An in-line filter is
required for drawer models with an ice maker when water
conditions have a high sediment content.
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi
constant water pressure of 35–120 psi
(2.4–8.3 bar)
supplied
to the unit at all times. In this application, the water filtra-
tion system must be bypassed. Refer to water filter bypass
on page 15. A copper line is not recommended for this
application.
tion system must be bypassed. Refer to water filter bypass
on page 15. A copper line is not recommended for this
application.
PLUMBING REQUIREMENTS
Water Supply Line
1
/
4
" OD copper, braided
stainless steel or PEX tubing
Water Pressure
35–120 psi
(2.4–8.3 bar)
Excess Water Line for Connection
36"
(914)
WATER SUPPLY LOCATION
WIDTH
A
18" Models
3"
(76)
24" Models
5
1
/
2
"
(140)
30" Models
6"
(152)
36" Models
9"
(229)
A
1
/
4
"
(6)
1
/
4
"
(6)
4
1
/
4
"
(108)
4
1
/
2
"
(114)
FLOOR
LEFT SIDE
OF OPENING
Electrical supply location.
3"
(76)
6"
(152)
RIGHT SIDE
OF OPENING
AREA EXTENDS 1
/
2
"
(13)
FORWARD ON FLOOR
A
Water supply location.