Maytag MEDB750YW Installationsanweisungen

■

Is the dryer located in a closet?

Closet doors must have ventilation openings at the top and

bottom of the door. The front of the dryer requires a minimum

of 1" (25 mm) of airspace, and, for most installations, the

rear of the dryer requires 5" (127 mm). See "Installation

Instructions".

W10392124A

W10392125A-SP

7/11

Printed in U.S.A.

DRYER RESULTS
Clothes are not drying satisfactorily, drying times are

too long, or load is too hot

■

Is the lint screen clogged with lint?

Lint screen shold be cleaned before each load.

■

Is the exhaust vent or outside exhaust hood clogged with

lint, restricting air movement?

Run dryer for 5-10 minutes. Hold your hand under the outside

exhaust hood to check air movement. If you do not feel air

movement, clean exhaust system of lint or replace exhaust

vent with heavy metal or flexible vent. See “Installation

Instructions”.

■

Are fabric softener sheets blocking the grille?

Use only one fabric softener sheet, and use it only once.

■

Is the exhaust vent the correct length?

Check that the exhaust vent is not too long or has too many

turns. Long venting will increase drying times. See "Installation

Instructions".

■

Is the exhaust vent diameter the correct size?

Use 4" (102 mm) diameter vent material.

■

Is the dryer located in a room with temperature below

45°F (7°C)?

Proper operation of dryer cycles requires temperatures above

45°F (7°C).

® Registered Trademark/TM Trademark of Whirlpool, U.S.A., Whirlpool Canada LP licensee in Canada

® Registered trademark/™ Trademark of Maytag Properties, LLC or its related companies.

Used under license by Maytag Limited in Canada.

Dryer displaying code message

■

"PF" (power failure), check the following:

Was the drying cycle interrupted by a power failure?

Press and hold START/PAUSE to restart the dryer.

■

“L2” Diagnostic Code (low or no line voltage condition):

The drum will turn, but there may be a problem with your

home power supply keeping the dryer’s heater from turning

on. The dryer will continue to run when this diagnostic code

is present.

Press any key to clear the code from the display and return

to the estimated time remaining.

Try the following:

Check to see if a household fuse has blown or circuit breaker

has tripped. Electric dryers use two household fuses or

breakers. Replace the fuse or reset the circuit breaker.

Confirm the power cord is properly installed. Refer to

“Electrical Connection” for details.

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, consult a qualified electrician.

■

“E” Variable (E1, E2, E3) service codes:

Call for service.

No heat

■

Has a household fuse blown, or has a circuit breaker

tripped?

The drum may be turning, but you may not have heat. Elelctric

dryers use two household fuses or circuit breakers.Replace

the fuse or reset the circuit breaker. If the problem

continues, call an electrician.

■

Is “Check Vent” illuminated on the Airflow screen?

This indicator will show the status of airflow through the dryer

vent. The Detecting light comes on during the sensing phase

at the beginning of a cycle. THe Check Vent light will come

on if a blocked vent or low airflow issue is detected.

Try the following:

Clean lint screen.

Check to see if the vent run from the dryer to the wall is free

of lint and debris.

Confirm the exterior vent exhaust hood is free of lint and

debris.

Confirm your vent system falls within the recommended run

length and number of elbows for the type of vent you are

using. Refer to “Plan Vent System” for details.

Select a Timed Dry heated cycle, and restart the dryer.
For more information on maintaining good airflow, see

“Check Your Vent System for Good Airflow” in the “Use and

Care Guide”. If the message persists, have your entire home

venting run cleaned.