Maytag MVWB835DW Benutzung Und Pflege

Touch to turn the washer on and off. Touch to stop/cancel a  

cycle at any time. 

Use the Wash Cycle knob to select available cycles on your 

washer. Turn the knob to select a cycle for your laundry load.  

See “Cycle Guide” for detailed descriptions.

The Estimated Cycle Time display shows the time required for 

the cycle to complete. Factors such as load size and water 

pressure may affect the time shown in the display. Overloading, 

unbalanced loads, or excessive suds may cause the washer to 

adjust the cycle time as well. 

Use “+” and “–” to delay the start of the wash cycle by up to  

12 hours. To turn off Delay Start, use “+” and “–” to set the  

delay time to “0,” or touch POWER.

Touch and hold START/PAUSE button for up to 3 seconds or 

until the washer starts to begin the selected cycle; touch again  

to pause a cycle.
NOTE: If the washer is spinning, it may take several minutes  

to unlock the lid.

The following options may be added to most cycles. 

Wash temperature senses and maintains uniform water 

temperatures by regulating incoming hot and cold water. 

Select a wash temperature based on the type of fabric 

and soils being washed. For best results and following the 

garment label instructions, use the warmest wash water safe 

for your fabric.

•  On some models and cycles, warm and hot water may be  

  cooler than your previous washer.

•  Even in a cold and cool water wash, some warm water may  

  be added to the washer to maintain a minimum temperature.
SOIL LEVEL

Select the most suitable setting for your load. For heavily 

soiled items, select Extra Heavy Soil Level for more wash  

time. For lightly soiled items, select Extra Light Soil Level  

for less wash time.
Lighter soil level setting will help reduce tangling and 

wrinkling.
SPIN SPEED

Select the most suitable setting for your load.

The following options may be added to most cycles. 

This washer is designed to dispense laundry boosters such 

as oxygenated stain treaters and color-safe bleach at the 

right time in the cycle for best cleaning performance. Do not 

use laundry boosters and chlorine bleach in the same cycle.
EXTRA RINSE

This option can be used to automatically add a second rinse 

to most cycles.
NOTE: If you want to Drain and Spin only, select the Rinse & 

Spin cycle and then, touch to turn off the Extra Rinse option.
DEEP CLEAN

This option provides enhanced cleaning action for tough 

stains. It will add additional agitation and soak time to the 

cycle.
AUDIO LEVEL

Use this option to adjust volume of the signal that sounds at 

the end of cycle and key pad sounds. Touch once for low, a 

second time for off, and a third time to loop back to high. A 

higher signal is helpful in removing items as soon as cycle is 

complete. Default setting is high.

The Cycle Status Lights show the progress of a cycle. At each 

stage of the process, you may notice sounds or pauses that are 

different from traditional washers.

When the START/Pause button is touched, the washer will 

first perform a self-test on the lid lock mechanism. You will 

hear a click, the basket will make a slight turn, and the lid will 

unlock briefly before locking again. 

Once the lid has locked the second time, the washer will use 

short, slow spins to estimate the load size. These sensing 

spins may take 2 to 3 minutes before water is added to the 

load and you may hear the hum of these spins. If the sensing 

light is on, then washer is working properly. You will hear the 

motor turn the basket in short pulses to thoroughly wet the 

load. The washer will then move the load briefly, pause to 

allow water to soak in to the load, and resume adding water. 

This process may repeat until the correct amount of water 

has been added for the load. You may also hear water flowing 

through the dispenser, adding detergent to the load. 
NOTE: Avoid opening lid during sensing. The sensing 

process will start over when the washer is restarted. The 

sensing light may also come on during the Wash portion of 

the cycle. This is normal. 

NOTE: The control panel features a sensitive surface that responds to a light touch of your finger. To ensure your selections are registered, 

touch the control panel with your finger tip, not your fingernail. When selecting a setting or option, simply touch its name until the desired 

section is illuminated.