Dacor RNR30NC Installationsanweisungen

Product Specifications

IMPORTANT: Observe all governing codes and ordinances 

during planning and installation. Contact your local building 

department for further information.

Electrical Requirements (All models 

numbers except those ending with -C)

It is the owner’s responsibility to ensure that a licensed electrician 

performs the installation of the power supply for this appliance. 

The electrical installation, including minimum supply wire size, 

must comply with the National Electric Code ANSI/NFPA 70 (latest 

revision) and local codes and ordinances.

 A copy of this standard 

may be obtained from: 

National Fire Protection Association 

1 Batterymarch Park 

Quincy, Massachusetts 02269-9101

The correct voltage, frequency and amperage must be supplied 

to the appliance from a dedicated, grounded, single phase circuit 

that is protected by a properly sized circuit breaker or time-delay 

fuse. If a time-delay fuse is utilized, fuse both sides of the line (L1 

and L2).

240 Vac 60 Hz, 4-wire*, 50 Amp.

11.5 kW (48.0 Amp.)

* Two 120 Vac hot (L1 and L2), one neutral (N1) and one ground.
The above electrical specifications are for reference only. See the 

product data label for exact specifications. See inside cover for 

location.
• 

The wiring needs to be long enough to allow the range to be 

pulled out for service, while remaining connected.

• 

The wiring connected to the range must:
◊  Meet NEMA standards and have a minimum rating of 

250 Volts @ 50 Amp.

◊  Include a strain relief.
◊  Be terminated by tinned leads, closed loop terminals or 

open ended spade lugs with upturned ends.

◊  Connect to a junction box or receptacle installed by a 

licensed electrician.

The appliance may be connected one of the following ways:
• 

Using conduit: 
◊  A 4-wire conduit connected to a 4-wire junction box, or
◊  A 3-wire conduit (where local code permits) connected to 

a  3-wire junction box.

Suggested conduit wiring color code: black, white, red and 

green.

• 

Using an appliance cord:
◊  A 4-wire appliance cord equipped with a NEMA 14-50P 

plug connected to a NEMA 14-50R receptacle, or

◊  A 3-wire appliance cord (where local code permits) 

equipped with a NEMA 10-50P plug connected to a 

NEMA 10-50R receptacle.

Appliance cord plug must be UL listed type SRD or SRDT.

Electrical Requirements 

(Models Ending with -C)

Range models RNR30NS-C, RNR30NFS-C, RNR30NIS-C and 

RNR30NIFS-C come with a factory installed 4-wire appliance cord 

with NEMA 14-50P plug.
• 

For freestanding ranges installed in Canada, a factory 

installed 4-wire appliance cord with NEMA 14-50P plug is 

required, without modification. For slide-in ranges installed in 

Canada and all ranges installed outside of Canada, the 4-wire 

appliance cord configuration (-C type) is optional and may be 

utilized where local codes permit. 

• 

The NEMA 14-50P plug is designed to plug directly into 

a NEMA 14-50R electrical receptacle. It is the owner’s 

responsibility to ensure that the required 4-wire electrical 

outlet compatible with the power cord is installed by a 

licensed electrician as specified below prior to range 

installation. The electrical outlet installation, including 

minimum supply wire size and grounding, must be in 

accordance with all governing codes and ordinances. 

• 

The correct voltage, frequency and amperage must be 

supplied to the appliance from a separate, grounded, circuit 

that is protected by a properly sized circuit breaker or time 

delay fuse. If a fuse is utilized, fuse both sides of the line (L1 

and L2). Refer to the ratings on the product data label.

240 Vac 60 Hz, 4-wire*, 50 Amp.

11.5 kW (48.0 Amp.)

* Two 120 Vac hot (L1 and L2), one neutral (N1) and one ground.
The ratings above are for reference only - refer to the product 

data label (see inside cover).