Dacor ER48D Installationsanweisungen

Planning the Installation

Cabinet Layout

• 

Carefully check the location where the range is to be 

installed. For best performance, the range should be placed 

away from drafts that may be caused by doors, windows and 

heating and air conditioning outlets.

• 

To reduce the risk of personal injury and to reduce 

accumulated smoke in the room, Dacor strongly recommends 

installing a range hood. A range hood should project 

horizontally a minimum of 5 inches beyond the face of the 

cabinets.

• 

All maximum and minimum dimensions and clearances 

shown in the diagrams below must be maintained for safe 

operation.

• 

The range may be installed flush to the rear wall. Dacor 

strongly recommends installing a non-combustible material 

on the rear wall above the range and up to the vent hood or 

installation of a backguard. It is not necessary to install non-

combustible materials behind the range below the countertop 

height.

• 

Any openings in the wall behind the appliance or in the floor 

underneath it must be sealed.

Gas and Electrical Service

• 

The shaded area shown denotes the suggested location of 

the gas inlet and the electrical junction box/receptacle. For 

replacement purposes, the location of the existing utilities 

may be utilized provided they do not interfere with the 

sides or rear of the range. Check local building codes for 

permissible gas valve locations.

• 

An external manual shut-off valve must be installed between 

the gas inlet and the range, for the purpose of turning on or 

shutting off gas to the appliance.

• 

Access to the gas shut-off valve when the unit is installed.

• 

Access to the remote circuit breaker panel/fuse box, when the 

range is in place.

• 

The gas supply piping and shut-off valve, and the electrical 

junction box/receptacle must be located so they do not 

interfere with the range when it is installed.

• 

The junction box and gas shut off valve must be located 

so that the range can be pulled out for service while the 

appliance remains connected.

Note 2

F

G

2

 Cabinet/countertop depth is at discretion of customer but 

cabinet face MUST NOT protrude further than rear of front 

panel, see product dimensions.

3

 Vertical distance from range top panel level.

1

 Vertical to combustible surface from range grate level; if 

installing an overhead vent hood, also check the hood 

specifications for minimum required clearances. 

Non-combustible 

surface along 

back wall

recommended

10” (25.4 cm) min.

to combustible side

walls above the range

(both sides)

30” (76.2  cm)

min.

1

36 1/2” 

(92.7 cm)

max.

13” (33.0 cm)

max.

4

18” (45.7 cm)

min.

3, 4

Suggested 

location of 

utilities

 

3

4

 This specification does not apply for cabinets more 

than a horizontal distance of 10” (25.4 cm) from the 

edge of the range.

G

10" (25.4 cm) min.
to combustible side
walls above the range
(both sides)

non-combustible

Minumum  Countertop Height:

30 1/4” (76.8 cm) 

Maximum  Countertop Height:

36 1/2” (92.7 cm)

rear wall recommended

Backsplash

3/8" (1.0 cm)

Min. flat countertop

overhang

H

2 13/16"

(7.1 cm)

Note 2

Cutout tolerances: +1/16” (+1.6 mm), -0 

unless otherwise stated

ER36D

42” (106.7 cm)* 

36” (91.4 cm)**

36 1/16” 

(91.6 cm)**

33 1/2” 

(84.8 cm)

ER48D

54” (137.2 cm)* 

48” (121.9 cm)**

48 1/16” 

(122.1 cm)**

43 1/2” 

(110.2 cm)

* Recommended ** Minimum

ER36D

ERV36-ER

ER48D

ERV48-ER

IMPORTANT: See the downdraft installation instructions 

for the duct and electrical installation requirements. Use 

only the downdraft vent models specified above.