Dacor DR30DHLPH Technisches Handbuch

All specifications subject to change without notice.

Phone: (800) 793-0093

www.dacor.com

Document # PGCI-026

Revised 01/13/12   Page 2/2

Cabinet tolerances: -1/16”, (+1.6 mm) -0

Cabinet face

Range side

panel removed

Countertop

Range trim resting

on countertop

Back of control

panel and trim

behind door

rest against

cabinet face 

DR30DI range

3/8” min. (1.0 cm)

flat countertop

overhang required 

behind cutout

ERV3015

raised vent

3/8” min. (1.0 cm) space

required behind ERV3015

chassis to clear stiffener

H

rear wall recommended

Non-combustible

countertop and

cabinet opening

29 1/4” (74 3 cm)

27 1/2” (69.9 cm)

2 9/16”

 (6.5 cm)

10” min.

(25.4 cm)

both sides

Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm) 

Notch countertop to

3/8” min. (1.0 cm)

countertop

overhang

raised vent  opening

H

Combustible side

wall above range

below countertop

Cabinet face

To countertop

 front

K

30” (76.2 cm)

Countertop and

Cabinet Front

Self-Rimmed,

20 5/8” *

(52.4 cm)

NA

0” (0 cm) to

5 3/8” (13.7 cm)

Countertop and

Cabinet Front

Self-Rimmed (side

panels removed)

23 7/8” *

(60.6 cm)

NA

0” (0 cm) to

2 1/8” (5.4 cm)

* Cabinet face below countertop must be flush with back of notch in 

countertop
Countertop height for all self-rimming installations:  

35 7/16” (90.0 cm) minimum, 37 7/16” (95.1 cm) maximum

 

■

Only model DR30DI may be installed with a raised vent. Use only 

Dacor raised vent model ERV3015.

 

■

A self-rimming countertop configuration is required for raised vent 

installation. On installations with a raised vent, when sliding the range 

into position, it will stop when the rear of the control panel or side 

panels contact the notches toward the front of the countertop.

 

■

The self-rimming installation of the DR30DI range and ERV3015 

raised vent create a “built-in” look where the range trim overlaps the 

countertop on both sides and the raised vent overlaps the countertop 

in back. It is also possible, if the cabinets are deep enough, to self 

rim the front of the range into the cabinet face immediately behind the 

control panel and door trim or behind the side panels (see below). 

The rear range trim will partially cover the front of the raised vent 

chassis in back.

Cabinet face

Countertop

Range trim resting

on countertop

Back of

side panel

rests against

cabinet face 

DR30DI range

3/8” min. (1.0 cm)

flat countertop

overhang required 

behind cutout

3 1/4 inch

side panel

ERV3015

raised vent

3/8” min. (1.0 cm) space

required behind ERV3015

chassis to clear stiffener

H

rear wall recommended

Non-combustible

countertop and

cabinet opening

29 1/4” (74 3 cm)

27 1/2” (69.9 cm)

2 9/16”

 (6.5 cm)

10” min.

(25.4 cm)

both sides

Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm) 

Notch countertop to

3/8” min. (1.0 cm)

countertop

overhang

raised vent  opening

H

Combustible side

wall above range

below countertop

Cabinet face

To countertop

 front

K

30” (76.2 cm)

A

A

A

A

C

C