Dacor MH3018S Designanleitung

Seite von 1
PLANNING
GUIDE
Web: http://www.Dacor.com
Corporate Phone: 800-793-0093
Specifications are subject to change without notice.
See installation instructions for additional details.
6.1
Duct Planning
DUCT PLANNING
WARNINGS:
1.  To reduce the risk of fire and to properly exhaust 
air, ducted fans must be vented to outside. Do not 
vent exhaust air into spaces within walls, ceilings, 
attics, crawl spaces or garages.
2.  Improper installation, adjustment, alteration, 
service or maintenance can cause personal injury 
or property damage
3.  To reduce the risk of fire, use only ductwork 
materials deemed acceptable by state, municipal 
and local codes.
NOTES:
1.  Best performance is achieved by using round duct 
instead of rectangular, especially when elbows are 
required.  
2.  If multiple elbows are needed, ensure that there is 
a minimum of 24”of straight duct between any two 
elbows. 
3.  Avoid “S” or “back to back” configurations caused 
by adjacent elbows. 
4.  Thermal breaks, such as a short section of non-
metallic duct, should be used in areas of extreme 
cold.  
5.  A back-draft damper at the duct outlet may also be 
required.
6.  Do not use flexible metal duct. 
7.  Do not use ductwork that is smaller in cross-
sectional area than the recommended size duct.
8.  Do not rely on duct tape alone to seal duct joints. 
Use sheet metal screws as required to support the 
duct weight.
9.  The vent hood and cooking appliance(s) must be 
removable if service is required.
10.  Be certain that the ductwork does not interfere with 
floor joists or wall studs.
11.  It is important to keep as few turns in the duct run, 
and to keep the run as short as possible.
12.  Do not restrict the air flow by reducing the duct 
cross-sectional areas when making hard joints or 
squeezing through a tight area.
Higher volumes of air exhausted by the vent system result in better 
overall removal of smoke and fumes from the kitchen.  Longer duct runs 
and greater numbers of duct transitions reduce air volume, therefore 
it 
is extremely important to keep duct runs as short and straight as 
possible.
To ensure that your installation meets this requirement, add the actual 
straight length of duct to the equivalent straight length of all duct fittings to 
determine the total equivalent straight length of duct. (Refer to the table 
below. Consider the duct size that corresponds to the majority of the duct 
used in the installation.
After determining that your proposed ductwork meets the maximum duct 
length requirement, proceed with the location planning.
Equivalent Straight Feet
90° Elbow, 3 1/4” x 10”
15 ft.
90° Elbow, 8” Round
7 ft.
90° Elbow, 10” Round
5 ft.
45° Elbow, 3 1/4” x 10”
7 ft.
45° Elbow, 8” Round
3 ft.
45° Elbow, 10” Round
2 ft.
Straight Transition, 3 1/4” x 10” to 8” Round
4 ft.
Straight Transition, 3 1/4” x 10” to 10” Round
4 ft.
90° Transition, 3 1/4” x 10” to 8” Round
25 ft.
90° Transition, 3 1/4” x 10” to 10” Round
25 ft.
1/1
PLANNING
GUIDE
Revised
02/04/08
13.  With concrete slab construction, "box-in" the 
ductwork to prevent it from collapsing when 
the wet concrete is poured. Also allow room for 
electrical conduit.
14.  Cross-drafts or air currents caused by adjacent 
open windows or doors, HVAC outlets, ceiling fans 
and recessed ceiling lights reduce vent efficiency.