Panasonic AJ-SDX900p Benutzerhandbuch

Seite von 102
24
Chapter 3  Recording and playback
3-7
RETAKE function
The RETAKE function ensures continuity with the previous cut
on the tape when shooting is resumed.
It is set by opening the <REC FUNCTION> screen from the
SYSTEM SETTING page and selecting ON as the setting for
the RETAKE MODE item by performing menu operations.
The RETAKE MODE item settings are described below.
ON: The retake operation is performed when the RET button
on the lens is pressed while the MODE CHECK button
is held down.
OFF: The RETAKE function does not operate.
If, when the rec pause mode is established upon completion
of the recording or the stop mode is established afterwards,
the RET button on the lens is pressed while the MODE
CHECK button is held down, the tape will be rewound to the
approximate start point (a position advanced by 10 or so
frames from the recording start) of the final image that was
last recorded, and the rec pause mode will be established.
If there is some leeway in the shooting time and a “NG”
condition has been clearly identified, recording can be started
from this point, and the cut in the NG area will be deleted.
This function is particularly useful for cutting the amount of
time taken for copying onto work tapes and other such
economical operations.
3-9
Normal playback and
playback at different
speeds
Black-and-white playback images can be viewed in the
viewfinder by pressing the PLAY button.  At the same time,
color playback images can be viewed if a color video monitor
is connected to the unit’s VIDEO OUT connector and MON
OUT connector.  Furthermore, playback images using SDI
can be viewed from the VIDEO OUT connector when the AJ-
YA902G expansion board has been installed.  (In order to
view these images, the OUTPUT SEL switch on the side
panel must be set to the VTR position.)
In addition, when the FF and REW buttons are used, the
images can be played back at different speeds by establishing
the cue mode (PLAY + FF), review mode (PLAY + REW),
high-speed fast forward playback mode (FF) or high-speed
rewind playback mode (REW).
3-8
Rec review function
When recording is temporarily stopped and the lens RET
button is pressed, the last two seconds of the tape are
automatically rewound, and the playback pictures on this part
of the tape appear on the viewfinder screen.  This makes it
possible to check whether recording was performed properly.
After the two seconds of the tape have been played back, the
unit is again set to the recording start standby mode.
If the RET button is held down, a maximum of 10 seconds of
the tape is rewound and played back.
The RET button function can be allocated by opening the
<USER SW> screen from the OPERATION page and
selecting settings for the USER MAIN SW, USER1 SW and
USER2 SW items by performing menu operations.
<Note>
The rec review function cannot be used unless recording
lasts for one or more seconds.
If the OUTPUT SEL switch on the side panel is at the VTR
position during the rec review operation, the rec review
images are output not only to the viewfinder but to the video
output connectors (VIDEO OUT connector and MON OUT
connector) as well.  Bear in mind that if back-up images are
being recorded by a backup VTR that has been connected,
these rec review images will end up being recorded.
When the RETAKE function is to be exited
There are two ways to do this.
1) Set the unit’s POWER switch to OFF.
2) Perform a menu operation and select OFF as the
RETAKE MODE item setting.
Direction of tape travel
Approx. 10 frames
Cut 1
Cut 2
Cut 1
Cut 2
Cut 3
Cut 3
Cut 4
Direction of tape travel
Playback of recorded section
Recording section
2 to 10 sec.
No recorded or already recorded section
Rec pause
Rec pause
Rec review operation
When the AJ-YA903G board has been installed in the unit
and, play, FF or REW operations are performed following
one shot recording, these operations will be performed after
the images remaining in the memory have been recorded
onto the tape. While the images are being recorded, the
LED of the button pressed (for play, FF or REW operation)
will flash.
Concerning the time code display (when AJ-YA903G is
installed)
When recording has been started, the time code (TCG)
display may remain in the hold status until it is possible for
the time code (TCR) on the tape to be read.