Mitsubishi Electronics DX-TL1600EM Benutzerhandbuch

66

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

♦

RS-232C

1

6 9

5

2

3

4

5

RXD

TXD

DTR

GND

Receiving Data

Transmission Data

Data Terminal Ready

Signal Ground

Pin NO. Letters

Letters

Pin NO.

Transmition Contents

Transmition Contents

6

7

8

DSR

RTS

CTS

Data Set Ready

Transmission 

Requirement

Transmission Clear

♦

Please use the following RS-232C Crossover cable to connect your personal computer to the Unit.

FRAME

D-SUB 9 pin (unit)

D-SUB 25 pin(Personal computer)

FG
TXD
RXD
RTS
CTS
DSR
GND
DTR

1
2
3
4
5
6
7

20

RXD

TXD

DTR

GND

DSR

RTS
CTS

2
3
4
5
6
7
8

1) When RS-232C terminal of personal 
computer is D-SUB 25 pin

   

D-SUB 9 pin

D-SUB 9 pin

FRAME

FRAME

RXD
TXD
DTR
GND
DSR
RTS
CTS

2
3
4
5
6
7
8

RXD

TXD

DTR

GND

DSR

RTS
CTS

2
3
4
5
6
7
8

2) When Pesonal cpmputers RS-232C 
terminal is D-SUB 9 pin

♦

The settings can be made on RS-232C SETTING of the <REAR TERMINAL> menu. Set the Unit and the modem or a personal
computer with same settings. Please refer to the diagram for possible setting rate.

1

2

3

4

5

TRANSMISSION

RATE

DATA BIT LENGTH

PARITY BIT

STOP BIT

DELIMITER

1200/2400/4800/

9600

8 BIT/7 BIT

NONE/ODD/EVEN

1 BIT/2 BIT

CR/CR•LF

Synchronization

Name on Menu

Asynchronous

1

2

3

X control

S parameter

CS-RS hamd-shake

Not available

Not available

Available

Synchronization

Name on Menu

# Set other functions on the personal
computer as shown below.

Transmission rate at
the data received/
sent

Data bit length

Parity bit setting

Stop bit length

Line feed setting

 Please note that the RS-232C interface (located on the back of the unit) does not function while the unit is in commu-

nication mode.

■

Operation and setting of this unit by a personal computer is executed by command codes and error codes.

Delimeter

(sending) #1

Delimeter

(receiving) #2

Parameter 1

Parameter n

Command code

Status

Parameter 2

Parameter 1

Parameter n

Parameter 2

,

,

,

• • • • • • • • • •

• • • • • • • • • •

• • • • • • • • • •

• • • • • • • • • •

1) Command : an order from a personal computer to the unit

2) Command : a reply from the unit ( indicated on a personal computer)

,

,

,

#1: If you set the DELIMITER setting to "CR" on the RS-232C setting menu, 
input a Carrige return code (0DH). 
If you set the DELIMITER setting to "CR • LF" on the RS-232C setting menu,
input a carrige return code (0DH) and a line 

****

code (0AH). 

#2: If you set the DELIMITER setting to "CR" on the RS-232C setting menu, 
output a Carrige return code (0DH). 
If you set the DELIMITER setting to "CR • LF" on the RS-232C setting menu,
output a carrige return code (0DH) and a line 

****

code (0AH). 

Make sure to send commands in an interval of 0.1 second.

♦

PW1

CR

RC

EX

CR

CR

Example 1) Turn the Unit on.( when DELIMITER is set to "CR" on the RS-232C setting menu)

Command from 

personal computer

Replied status code from uint
to a personal computer

Meaning

Sending a command to turn the Unit on.

The unit received a command and executed.

The unit received a command.