Sony HKCU-953 Benutzerhandbuch
![Sony](https://files.manualsbrain.com/attachments/7e61ba04cadfce70cb41a1a70ef1d62a30f0a5fe/common/fit/150/50/682a2570dc00831b079177f57c62a2915dd3423eb752334060fbcf750d89/brand_logo.png)
1-19 (E)
HDCU-950 IMM
1-6. Setting of Switches on Boards
. S8 (EC POSITION SEL)
This switch is valid when S6 on the RC-91 board is set
to LOCAL.
When S7 on the RC-91 board is set to EC or LB, and
S10-3 and S10-4 on the RC-91 board are set to 13 : 9, 14
: 9, or 15 : 9, select the cutting position.
to LOCAL.
When S7 on the RC-91 board is set to EC or LB, and
S10-3 and S10-4 on the RC-91 board are set to 13 : 9, 14
: 9, or 15 : 9, select the cutting position.
CENT : Cuts out the center.
VAR : Changes the horizontal cutting position with
VAR : Changes the horizontal cutting position with
S9 on the RC-91 board.
Factory setting : CENT
. S9 (EC POSITION CONT)
This switch is valid when S6 on the RC-91 board is set
to LOCAL.
When S8 on the RC-91 board is set to VAR, adjust the
horizontal cutting position.
to LOCAL.
When S8 on the RC-91 board is set to VAR, adjust the
horizontal cutting position.
S8
The cutting position moves left.
LEFT
The cutting position moves right.
RIGHT
. S10
Factory setting : All OFF
-1 (MONI) :
Selects whether the SD SDI OUT2 connector on the rear
panel is set or not as SD SDI MONITOR output.
-1 (MONI) :
Selects whether the SD SDI OUT2 connector on the rear
panel is set or not as SD SDI MONITOR output.
ON : SD SDI MONITOR
OFF : SD SDI (MAIN)
OFF : SD SDI (MAIN)
-2 : Not used.
-3, -4 (LB0/LB1 SEL) :
These switches are valid when S6 on the RC-91 board is
set to LOCAL.
When S7 on the RC-91 board is set to LB, select the
aspect ratio (13 : 9, 14 : 9, 15 : 9 or 16 : 9) of the picture.
-3, -4 (LB0/LB1 SEL) :
These switches are valid when S6 on the RC-91 board is
set to LOCAL.
When S7 on the RC-91 board is set to LB, select the
aspect ratio (13 : 9, 14 : 9, 15 : 9 or 16 : 9) of the picture.
S10-3
S10-4
Aspect ratio
OFF
OFF
16 : 9
OFF
ON
15 : 9
ON
OFF
14 : 9
ON
ON
13 : 9
-5 (MIN-DLY) :
Regardless of the setting of S417 on the AT-149 board,
down-conversion to the SD signal is performed with the
minimum delay.
Regardless of the setting of S417 on the AT-149 board,
down-conversion to the SD signal is performed with the
minimum delay.
ON : Minimum delay
OFF : Normal mode (Depends on the setting of S417
OFF : Normal mode (Depends on the setting of S417
on the AT-149 board.)
-6 (WF-SYNC) :
When mode other than ENC is selected in WF output,
this switch sets whether SYNC is added or not.
-7 (Bar CHARACTER OFF) :
Sets the character with a bar added to the SD signal to
OFF.
When mode other than ENC is selected in WF output,
this switch sets whether SYNC is added or not.
-7 (Bar CHARACTER OFF) :
Sets the character with a bar added to the SD signal to
OFF.
ON : Forced-OFF
OFF : Normal mode
OFF : Normal mode
-8 (PIX CHARACTER OFF) :
Selects whether the character signal is mixed or not to
the signal to be output from the PIX connector on the
rear panel.
Selects whether the character signal is mixed or not to
the signal to be output from the PIX connector on the
rear panel.
ON : Forced-OFF (Not mixed)
OFF : Normal mode (Mixed)
OFF : Normal mode (Mixed)
. S11-1 to 8
Factory use only
Factory setting : All OFF
Factory setting : All OFF
. 301 (SEQ CONT POLARITY)
Set this switch according to the used waveform monitor.
+ : PNP open collector output
_ : NPN open collector output
_ : NPN open collector output
Factory setting :
_