Meco 2410 Benutzerhandbuch
IGNITION LIGHTING THE SIDE BURNER
1. Remove Side Burner Cover if on.
2. Important: Make sure Side Burner Control Knob is
2. Important: Make sure Side Burner Control Knob is
turned “Off” first.
3. Turn Side Burner Control Knob on by rotating counter
clockwise. (FIG. 14A)
4. Push the Ignitor button in several times to light the
burner. Listen for the spark ignition and look to make
sure the burner is lit. If no spark, see (FIG. 14B) and
Troubleshooting Section.
sure the burner is lit. If no spark, see (FIG. 14B) and
Troubleshooting Section.
5. If Side Burner fails to light, repeat Steps 3 and 4.
If Side burner fails to light after three or four attempts
following Steps 3-4, turn control knob off by rotating
control knob clockwise until it stops. Wait five
minutes; then repeat the lighting procedure. NOTE: If
the burner still fails to light, refer to the
Troubleshooting Section. The burner can also be lit
manually, see Manual Lighting Side Burner.
following Steps 3-4, turn control knob off by rotating
control knob clockwise until it stops. Wait five
minutes; then repeat the lighting procedure. NOTE: If
the burner still fails to light, refer to the
Troubleshooting Section. The burner can also be lit
manually, see Manual Lighting Side Burner.
6. After ignition, turn the control knob to the desired
setting for use.
If the side burner goes out during operation, turn the
control knob to the “Off” position. Wait five minutes
before attempting to relight the grill. If it does not
relight, turn control knob to the “Off” position. Make
sure there are no open flames nearby, then disconnect
the cylinder and see if it is empty.
control knob to the “Off” position. Wait five minutes
before attempting to relight the grill. If it does not
relight, turn control knob to the “Off” position. Make
sure there are no open flames nearby, then disconnect
the cylinder and see if it is empty.
To reduce the risk of serious bodily injury or death:
· Use only 1 pound LP cylinder with Side Burner.
· Remove plastic Side burner cover before lighting the Side burner to prevent an explosion from gas build-up or
· Use only 1 pound LP cylinder with Side Burner.
· Remove plastic Side burner cover before lighting the Side burner to prevent an explosion from gas build-up or
melting of the cover.
· Make sure there are no obstructions to the flow of combustion and ventilation air to the side burner.
· During failed lighting attempts, or if the side burner goes out during the cooking process, turn control knob “Off”
· During failed lighting attempts, or if the side burner goes out during the cooking process, turn control knob “Off”
to dissipate any accumulation of gas. Wait five minutes before repeating lighting procedure.
· To avoid burns, keeps hands and fingers away from the burner ring when manually lighting with a match.
FIG. 14A
Ignitor Button
Turn Control
knob to “On”.
1. Remove Side Burner Cover if on.
2. Important: Make sure Side Burner Control Knob is
2. Important: Make sure Side Burner Control Knob is
turned “Off” first.
3. Hold a lit match near the burner. (FIG. 14C)
4. Turn Side Burner Control Knob to the “On” position.
4. Turn Side Burner Control Knob to the “On” position.
(FIG. 14A)
5. If Side Burner fails to light, repeat Steps 3 and 4.
If Side burner fails to light after three or four attempts
following Steps 3-4, turn control knob off by rotating
control knob clockwise until it stops. Wait five
minutes; then repeat the lighting procedure. NOTE: If
the burner still fails to light, refer to the
Troubleshooting Section.
following Steps 3-4, turn control knob off by rotating
control knob clockwise until it stops. Wait five
minutes; then repeat the lighting procedure. NOTE: If
the burner still fails to light, refer to the
Troubleshooting Section.
6. After ignition, turn the control knob to the desired
setting for use.
If the side burner goes out during operation, turn the
control knob to the “Off” position. Wait five minutes
before attempting to relight the grill. If it does not
relight, turn control knob to the “Off” position. Make
sure there are no open flames nearby, then disconnect
the cylinder and see if it is empty.
control knob to the “Off” position. Wait five minutes
before attempting to relight the grill. If it does not
relight, turn control knob to the “Off” position. Make
sure there are no open flames nearby, then disconnect
the cylinder and see if it is empty.
MANUAL LIGHTING THE SIDE BURNER
Hold lit match near burner ring.
14
FIG. 14B
FIG. 14C
Electrode
3/16” Gap from
Electrode to Burner
Turn Control knob
to “On”.