Fisher & Paykel 88388 EC120DXV1 Merkblatt

Seite von 2
104923 issue A 
ECN 06 037
 
 
 
 
Designer Series Island Canopy 
 
80327 EC120DXV1 (SS NZ/AUS) 
80328 EC120DMV1 (IR NZ/AUS) 
88388 EC120DXV1 (EU) 
88833 EC120DXV2 (UK) 
 
 
 
 
 
Please note product may vary slightly from the picture. 
Please read the entire instructions before installing the canopy. 
 
 
INSTALLATION INSTRUCTIONS
 
CONTENTS 
Contents of packaging 
Equipment required 
Optional accessories 
1 x canopy hood 
Electric drill 
Light bulb 
104467 
2 x chimney pieces 
Drill bits 
Chimney ext.(10’) SS 
 
8 x angle brackets 
Spirit level 
Chimney ext.(10’) IR 
 
1 x installation instructions 
Screwdriver 
Charcoal filter 
103821 
4 x filters (part number 104660) 
Jig saw 
Recirculation kit 
1744 
Installation kit (part number 104922) 
Ladder 
 
4 x 12 x 40mm screw  
Tape measure 
 
30 x 6 x ¼” self tapping screw 
Duct tape 
 
(2 spare) 
Ducting 
 
 
PRE-INSTALLATION 
 
Thank you for purchasing a quality, stainless steel canopy hood. 
We have a high standard of quality control and each canopy hood is tested and approved before it 
leaves the factory. 
 
IMPORTANT 
• 
Always switch the power off prior to installation, servicing or cleaning the canopy hood. 
• 
Never use the canopy hood without the filters. 
• 
Stainless steel is very easily damaged during installation if abraded or knocked by tools.  
Protect the top of the canopy with cardboard or polystyrene during installation. 
• 
Please read the entire instructions before installing the canopy hood. 
• 
A power outlet should be within 750mm from the motor assembly and can be either on the 
wall, behind the chimney or in the ceiling.  An extension lead may be necessary on some 
installations.
 
• 
To comply to electrical safety regulations this canopy must be plugged into a socket near the 
appliance.  The socket must be accessible and enable the end user to isolate the canopy from 
the power for the purpose of internal cleaning or maintenance.
 
 
Ducting accessories are not supplied.  All ducting must comply with local requirements and 
building codes. 
 
 
All electrical work must be done in accordance with local and/or national electrical 
codes as applicable.  For safety this product must be earthed.  If you are unfamiliar with 
methods of installing electrical wiring, employ the services of a qualified electrician. 
Turn off power at service entrance before installing wiring or servicing this product. 
lbs
 
The canopy hood is heavy please ensure adequate care when installing the canopy hood 
to prevent personal injury.  The canopy hood must be installed onto a solid wall or solid 
stud.  Weight of product 43.2 kg. 
 
HEIGHT OF CANOPY HOOD 
 
 
• 
The canopy is designed for 2440mm high ceilings. 
• 
The chimney is telescopic and is designed for hood installations 
between 600 to 750mm above the cooking surface. 
• 
Ascertain the desired installation height of the canopy hood. 
• 
Any installation above 750mm will compromise the extraction 
performance. 
• 
The air outlet from the motor requires 150mm round ducting 
which requires 170mm diameter hole in the ceiling. 
 
 
A=600 min (electric cook top) 
A=650 min (gas cook top) 
 
CONTROL PANEL 
 
Delay switch:  Canopy hood will remain on a 
low, mid or high speed for five minutes to clear 
away all residual cooking odours before 
switching off automatically
FILTER SURFACE
HOB TOP
A
I
I I
I I I
Fan On/Off
Mid Speed
High Speed            Delay Switch
Light On/Off