Beko UR584APW Benutzerhandbuch
EN
8
3
Installation
Transportation Instructions
1. The appliance should be
transported only in a vertical upright
position. The packing as supplied
must be intact during transportation.
2. If during the course of transport
the appliance has to be transported
horizontally, it must only be laid on its
right hand side when standing in the
frontof the appliance. After bringing
it to upright position,it must not be
operated for at least 4 hours to allow
the system to settle.
3. Failure to comply with the
above instructions could result in
damage occuring to the appliance.
The manufacturer will not be held
responsible if these instructions are
disregarded.
4. The appliance must be protected
against rain, moisture and other
atmospheric influences.
5. Empty any water in the drain tray
before moving see section “Defrosting”
and “Cleaning & Care” for further
information
IMPORTANT : Make sure the plastic
evaporating pan at the back of the
product collects water properly.
“IMPORTANT: Care must be taken
while cleaning / carrying the appliance
to avoid touching the bottom of the
condenser metal wires at the back of
theappliance as you might injure your
fingers and hands.
“IMPORTANT: This appliance is
not designed for stacking with any
otherappliance.When positioning your
appliance, take care not to damage
your flooring, pipes,wall coverings etc.
transported only in a vertical upright
position. The packing as supplied
must be intact during transportation.
2. If during the course of transport
the appliance has to be transported
horizontally, it must only be laid on its
right hand side when standing in the
frontof the appliance. After bringing
it to upright position,it must not be
operated for at least 4 hours to allow
the system to settle.
3. Failure to comply with the
above instructions could result in
damage occuring to the appliance.
The manufacturer will not be held
responsible if these instructions are
disregarded.
4. The appliance must be protected
against rain, moisture and other
atmospheric influences.
5. Empty any water in the drain tray
before moving see section “Defrosting”
and “Cleaning & Care” for further
information
IMPORTANT : Make sure the plastic
evaporating pan at the back of the
product collects water properly.
“IMPORTANT: Care must be taken
while cleaning / carrying the appliance
to avoid touching the bottom of the
condenser metal wires at the back of
theappliance as you might injure your
fingers and hands.
“IMPORTANT: This appliance is
not designed for stacking with any
otherappliance.When positioning your
appliance, take care not to damage
your flooring, pipes,wall coverings etc.
Do not move the appliance by pulling
by the door or handle.Do not attempt
to sit or stand on top of your appliance
as it is not designed forsuch use. You
could injure yourself or damage the
appliance.
“IMPORTANT:
by the door or handle.Do not attempt
to sit or stand on top of your appliance
as it is not designed forsuch use. You
could injure yourself or damage the
appliance.
“IMPORTANT:
Make sure that
mains cable is not caught under the
applianceduring and after carrying
/ moving the appliance, to avoid
the mains cablebecoming cut or
damaged.”Do not allow children to
play with the appliance or tamper with
the controls.
BEKO declines to accept any liability
should the instructions not be followed.
applianceduring and after carrying
/ moving the appliance, to avoid
the mains cablebecoming cut or
damaged.”Do not allow children to
play with the appliance or tamper with
the controls.
BEKO declines to accept any liability
should the instructions not be followed.
Installation Instructions
1. If possible avoid placing the
appliance near cookers, radiators or in
direct sunlight as this will cause the
compressor to run for long periods.
If installed next to a source of heat
or refrigerator, maintain the following
minimum side clearances:
From Cookers 2” (50 mm)
From Radiators 12” (300 mm)
From Refrigerators or Larder Fridge
1” (25 mm)
2. No gap is required at sides and top.
See item 3 below to ensure a gap is
obtained at the rear of the appliance.
If a gap is available on side and top,
retain it if possible as it would improve
the air circulation around the appliance.
3. Fit the two plastic wall spacers
supplied with the appliance rotating
1/4 turn to the condenser at the back
of the refrigerator (see diagram).
appliance near cookers, radiators or in
direct sunlight as this will cause the
compressor to run for long periods.
If installed next to a source of heat
or refrigerator, maintain the following
minimum side clearances:
From Cookers 2” (50 mm)
From Radiators 12” (300 mm)
From Refrigerators or Larder Fridge
1” (25 mm)
2. No gap is required at sides and top.
See item 3 below to ensure a gap is
obtained at the rear of the appliance.
If a gap is available on side and top,
retain it if possible as it would improve
the air circulation around the appliance.
3. Fit the two plastic wall spacers
supplied with the appliance rotating
1/4 turn to the condenser at the back
of the refrigerator (see diagram).