Intel MFSYS25 Merkblatt

Intel is a registered trademark of Intel Corporation or its

subsidiaries in the United States and other countries.

*Other names and brands may be claimed as the property

reserved.

E11186-003

*E11186-003*

Tools Required

Anti-static

wrist strap

Phillips*

screwdriver

Caution

Observe normal ESD

[Electrostatic Discharge]

procedures during system

integration to avoid possible

damage to compute module and/or

other components.

Warning

Installation and service of

this product to be performed

only by qualified service

personnel to avoid risk of injury from

electrical shock or energy hazard.

Warning

Read all caution and safety

statements in this document

before performing any of the

instructions. Also see the Intel

Server Board and Server Chassis

Safety Information document at:

http://support.intel.com/support/

motherboards/server/sb/cs-010770

.htm

for complete safety information.

Install System in Rack (Optional)

Storage Controller

Main Cooling Module

Power Supply Module

Ethernet Switch Module

Management Module

Chassis Back

I/O Cooling Module

Chassis Front

4(b) Finishing Up

THREE PEOPLE ARE REQUIRED TO LIFT THE

SYSTEM. If handles are present, remove the rear

handles prior to setting system onto slide rails.

Remove the front handles prior to sliding system

all the way into rail assembly.

Secure system to rack per rail kit installation

instructions.

Re-install all power supply modules, cooling modules,

the storage controller, the management module and the

Ethernet switch module. See the Intel® Modular Server

System MFSYS25 User Guide

for complete instructions on installing modules.

To re-install a power supply or cooling module:

■

Slide module into appropriate module

bay until retention latch engages.

To re-install a management module, storage controller

or Ethernet switch module:

■

Ensure retention lever is released and

rotated out and away from module.

■

Slide module into appropriate module

bay until bottom of retention lever

engages with bay.

■

Rotate retention lever in toward module

until it latches.

4(a) Preparation

Prepare rail system for rack mounting. Refer to the

Rail Kit Install Guide that is included with your rail

kit for instructions on assembling the kit.

Remove all modules from the Intel® Modular

Server System prior to lifting system into rack. This

includes all cooling modules, all power supply

modules, the management module, the Ethernet

switch module, and the storage controller. Refer to

adjacent illustrations for module location. See the

Intel® Modular Server System MFSYS25 User

Guide for complete instructions on removing modules.

To remove a power supply or cooling module:

Press retention latch to the left to

release module from module bay.

Slide module out of module bay.

To remove the management module, storage controller

or Ethernet switch module:

Press retention latch to the left to release

module from module bay.

Rotate retention lever out and away from

module.

Slide module out of module bay.

Three people ARE REQUIRED to lift the empty

system into the rack assembly. DO NOT lift

system while fully loaded.

Rear handles MUST BE removed prior to setting

system on rack rails. The profile of the handles

interferes with rack rails.

Front handles MUST BE removed prior to sliding

system all the way into rail assembly.

Install Pedestal
Feet (Optional)

Remove temporary handles if

present.

Lay chassis down horizontally.

Remove pedestal feet from strip

of sticky paper.

Affix one foot to each of the six

indent locations on the bottom

side of the chassis.

B
C

Install Temporary Handles (Optional)

Insert handle tabs into chassis slots.

Tighten captive screws.

NOTE: Handles are provided as

temporary devices to assist in

removing system from packaging

and for initial configuration.

DO NOT lift system

by power supply or

cooling module

handles.

Unpackaging
System

As packaged, the system

weighs 100 lbs. Install

temporary handles (see

Step 2) before lifting system

from shipping box.

Do not lift system from

packaging by power supply

or cooling module handles.

A minimum of three people

are required to lift system as

packaged.

Temporary handles will need

to be removed if system is

to be used in the pedestal or

rackmount configurations.

Package Contents

■

Intel® Modular Server System MFSYS25

■

Intel® Gigabit Ethernet Switch AXXSW1GB

plus one filler blank

■

Intel® Storage Controller plus one filler blank

■

Intel® Management Module

■

2 power supply modules

■

2 power supply blanks

■

1 I/O cooling module

■

2 main cooling modules

■

5 compute module blanks

■

2.5-inch SAS shared hard drive bay

■

14 hard drive carriers

■

Resource CD

■

This document

■

Attention Document

■

Rail kit

■

6 pedestal feet

If you are not familiar with ESD (Electrostatic Discharge) procedures
used during system integration, please see the Intel

Modular Server

System MFSYS25 User Guide, available at
http://support.intel.com/support/motherboards/server/MFSYS25

Read all cautions and warnings before starting your server system integration.

Thank you for buying an Intel

Modular Server System.

The following information will help you
assemble your Intel

Modular Server System MFSYS25

and install components.

This guide and other supporting documents
are located on the web at:
http://support.intel.com/support/motherboards/server/MFSYS25

Intel

Modular Server System

MFSYS25
Quick Start User's Guide