Toshiba 150 Benutzerhandbuch

6,08/$7,217528%/(&2'(6

+ 7KHUPLVWRURSHQ$QDO\VLVRIWKHWURXEOHFRGHLV

PDGHZLWK6,0

&KHFNIRUGLVFRQQHFWLRQRIWKHFRQQHFWRU&10&8
&KHFNIRUGLVFRQQHFWLRQRIWKHLQWHUIDFHFRQQHFWRU

5HSODFHWKHWKHUPLVWRU
5HSODFHWKH0&8
&KHFNWKHKHDWHUFRQWUROFLUFXLWLQWKH0&86SHFLILHGRQ60

++HDWHUKLJKWHPSHUDWXUHWURXEOH7KHWURXEOHFRGH

LVFDQFHOHGZLWK6,0

+HDWHUNHHSV21→6KRUWFLUFXLWLQWKHWULDF

6KRUWFLUFXLWLQWKHGULYHFLUFXLWRIWKHWULDFLQWKHSRZHU3:%
5HSODFHWKHWULDF
5HSODFHWKHSRZHU3:%

6KRUWFLUFXLWLQWKHWKHUPLVWRU6DPHFKHFNLWHPDVWKHUPLVWRURSHQ

8VH D WHVWHU WR FKHFN WKH WKHUPLVWRU LQWHUIDFH FRQQHFWRU 3LQFKHG

ZLUH

++HDWHUORZWHPSHUDWXUHWURXEOH7KHWURXEOHFRGHLV

FDQFHOHGZLWK6,0

&KHFNWKHLQVWDOOLQJHQYLURQPHQWURRPWHPSHUDWXUHSRZHUVXSSO\

YROWDJHRIWKHPDFKLQH

7KHKHDWHUODPSGRHVQRWOLJKWXS→([HFXWH6,0

+HDWHUODPSGLVFRQQHFWLRQ
&RQQHFWRUFKHFN&1SLQ+/287
&KHFNWKHKHDWHUODPSGULYHFLUFXLW2QWKHSRZHU3:%
&KHFNWKH+/287VLJQDO,I+/287LVQRWRXWSXWWHG→

5HSODFHWKH0&8

&KHFNWKHVLJQDOOLQHRI0&8DQG+/287VLJQDO

&KHFNIRULPSURSHUFRQQHFWLRQRIWKHWKHUPLVWRU

/6FDQQHUXQLWIHHGWURXEOH

/6FDQQHUXQLWUHWXUQWURXEOH

6KRUWFLUFXLWLQWKH0&83:% +/287VLJQDO

57+VLJQDO

&KHFNWKHFRQQHFWRU&1SLQ 0&8VLGH

3RZHUVXSSO\VLGH

CN120

MCU

Interface connector

Thermistor

Thermostat open

An abnormally high temperature
in the machine may cause the problem.
Check that the fan rotates normally.
(Similarly to H3-00.)

Check the setup of the kind of the fan.

SIM 26-63. The current setup is "2."

Sim 5-02
If the fan does not rotate normally,
check the fan connector and the
fan control signal. Replace the fax.

Use a tester to check the
AC line of the interface
connector. Replace the
fusing unit.

Check release of the headlock switch.

Check the scanner unit operation with SIM 1-01.

Does not operate.

Operates.

The shading sheet does not read.
The check item is the same as that of E7-10.

Check the connector. (CN103).

Check that the drive belt is properly applied to the scanner unit.

Check the drive signal of the scanner motor.

(OUT A+, A-, OUT B+, B-)

Abnormally heavy load of the scanner drive

(Improper engagement of the motor drive gear and the belt drive
gear)
(Abnormally high belt tension)

If there are no signals, replace the MCU.

If there are signals, replace the motor.

Follow the above signal line.

MHPS does not detect the home position. (MHPS, harness, PWB)