American Audio MCD-110 Benutzerhandbuch
SINGLE
TOTAL
REMAIN
TOTAL
REMAIN
TRACK
M
S
F
P IT C H
TIME
S G L
C TN
C TN
SINGLE
TOTAL
REMAIN
TOTAL
REMAIN
TRACK
M
S
F
P IT C H
TIME
S G L
C TN
C TN
SINGLE
TOTAL
REMAIN
TOTAL
REMAIN
TRACK
M
S
F
P IT C H
TIME
S G L
C TN
C TN
Activating the Pitch Slider (8):
To activate the PITCH SLIDER (8), you must turn the
pitch function on. Press the PITCH BUTTON (9) to turn
on the pitch function, when the pitch function is acti-
vated the PITCH LED (9) will begin to glow. If the pitch
function is not activated the PITCH SLIDER (8) will not
function.
pitch function on. Press the PITCH BUTTON (9) to turn
on the pitch function, when the pitch function is acti-
vated the PITCH LED (9) will begin to glow. If the pitch
function is not activated the PITCH SLIDER (8) will not
function.
12. PITCH ADJUSTMENTS
This function will increase or decrease the playback speed or "PITCH," of a track. The maximum pitch bend
percentage allowed is +/-16%. The PITCH SLIDER (8) is used to decrease or increase the playback pitch. If
the slider is move up (towards the top of the unit) the pitch will decrease, if the slider is moved down (towards
the bottom of the unit) the pitch will increase.
percentage allowed is +/-16%. The PITCH SLIDER (8) is used to decrease or increase the playback pitch. If
the slider is move up (towards the top of the unit) the pitch will decrease, if the slider is moved down (towards
the bottom of the unit) the pitch will increase.
Using the Pitch Slider (8):
To use the PITCH
SLIDER (8) slide the slider up and down. Down will
increase the pitch and up will decrease the pitch.
When the slider is in the center position, there is
zero pitch being applied to a track.
increase the pitch and up will decrease the pitch.
When the slider is in the center position, there is
zero pitch being applied to a track.
Figure 13
Figure 12
BASIC OPERATION
©
American Audio
®
- www.americanaudio.com - MCD-110™ Instruction Manual Page 15
11. CHANGING THE TIME DISPLAY (29, 30, & 31)/TIME BAR (24):
The time may be displayed in three different modes; Total Remain, Remain, and Elapsed. During normal play-
back, pressing the TIME BUTTON (11) as in figure 11, will change the time display information (29, 30, & 31) in
the LCD. The following is a break down of the time settings and their definitions:
back, pressing the TIME BUTTON (11) as in figure 11, will change the time display information (29, 30, & 31) in
the LCD. The following is a break down of the time settings and their definitions:
1) TOTAL REMAIN (27) - This details the time in the LCD (
29, 30, & 31
) as the current cds’ total remaining
time.
2) REMAIN (28) - This details the time in the LCD (
29, 30, & 31)
as the current tracks’ remaining running
time.
3) ELAPSED - This details the time in the LCD (
3) ELAPSED - This details the time in the LCD (
29, 30, & 31
) as the current tracks’ elapsed running time.
The unit will indicate the ELAPSED time when neither the TOTAL REMAIN OR REMAIN indica-
tors are showing.
tors are showing.
Note: When playing a Mp3 disc the TOTAL REMAIN time of a disc cannot be
shown. Only the REMAIN time and ELAPSED time of the track.
TIME BAR INDICATOR - The time bar in the LCD visually details the time defined in the TIME METER (
29, 30,
& 31
). This bar is also dependent on the selected time function; REMAIN (28) or TOTAL REMAIN (27).
This
bar will begin to flash when 15 seconds of a track remain and will begin to rapidly flash when three
seconds of a track remain. The flashing bar is a great visual reminder a track is about to end. The
flashing bar will function regardless of which time mode the unit is in.
seconds of a track remain. The flashing bar is a great visual reminder a track is about to end. The
flashing bar will function regardless of which time mode the unit is in.
Figure 11