ONKYO SKM-960S Benutzerhandbuch
93
Controlling Other Components
—Continued
Remote Control Codes for Onkyo
Components Connected via
Onkyo components that are connected via
are con-
trolled by pointing the remote controller at the AV
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
If you want to control an Onkyo component by pointing
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via
, use
the following remote control codes:
• [DVD] REMOTE MODE button
30627:
Onkyo DVD player without
(default)
• [CD] REMOTE MODE button
71817:
Onkyo CD player without
(default)
• [DOCK] REMOTE MODE button
6003:
Onkyo DS-A2 RI Dock without
(default)
Note:
• If you connect an
-capable Onkyo MiniDisc
recorder, CD recorder, or RI Dock to the TAPE
IN/OUT jacks, for
IN/OUT jacks, for
to work properly, you must set
Resetting the REMOTE MODE Buttons
You can reset a REMOTE MODE button to its default
remote control code.
remote control code.
You can reset the remote controller to its default settings.
1
Make sure the Onkyo component is con-
nected with an
nected with an
cable and an analog
audio cable (RCA).
2
Enter the appropriate remote control code
to the REMOTE MODE button.
to the REMOTE MODE button.
• [DVD] REMOTE MODE button
31612:
Onkyo DVD player with
• [CD] REMOTE MODE button
71327:
Onkyo CD player with
• [TAPE] REMOTE MODE button
42157:
Onkyo cassette recorder with
(default)
• [DOCK] REMOTE MODE button
6004:
Onkyo DS-A1 RI Dock with
See the previous page for how to enter remote
control codes.
control codes.
3
Press the REMOTE MODE button, point
the remote controller at the AV receiver,
and operate the component.
the remote controller at the AV receiver,
and operate the component.
1
While holding down the REMOTE
MODE button that you want to
reset, press and hold down the
[AUDIO] button until the Remote
indicator lights up (about 3 sec-
onds).
MODE button that you want to
reset, press and hold down the
[AUDIO] button until the Remote
indicator lights up (about 3 sec-
onds).
2
Within 30 seconds, press the
REMOTE MODE button again.
REMOTE MODE button again.
The Remote indicator flashes twice,
indicating that the button has been
reset.
Each of the REMOTE MODE buttons
is preprogrammed with a remote con-
trol code. When a button is reset, its
preprogrammed code is restored.
indicating that the button has been
reset.
Each of the REMOTE MODE buttons
is preprogrammed with a remote con-
trol code. When a button is reset, its
preprogrammed code is restored.
Resetting the Remote Controller
1
While holding down the
[RECEIVER] REMOTE MODE but-
ton, press and hold down the
[AUDIO] button until the Remote
indicator lights up (about 3 sec-
onds).
[RECEIVER] REMOTE MODE but-
ton, press and hold down the
[AUDIO] button until the Remote
indicator lights up (about 3 sec-
onds).
2
Within 30 seconds, press the
[RECEIVER] REMOTE MODE but-
ton again.
[RECEIVER] REMOTE MODE but-
ton again.
The Remote indicator flashes twice,
indicating that the remote controller
has been reset.
indicating that the remote controller
has been reset.
(3 seconds)
(3 seconds)
HT-S9100THX_En.book Page 93 Friday, June 27, 2008 4:00 PM