Sony 300PK Benutzerhandbuch
Chapter 4
Viewfinder Screen Indications and Menus
85
Chapter 4 Viewfinder Screen Indications and Menus
Advanced menu page 3
PAGE3 (NEXTm$ PREVm4)
mAWB MEM : 2
PRE. WHT : 3200
TONE : ON
BARS : SMPTE
a )
REMOTE1 : REC
REMOTE2 : MARK
BAUD RATE: 38400
EXIT MENU (YESmPUSH)
a)
For DSR-300P: EBU75
Item
Settings
GAIN
This sets gain values for the positions of the GAIN switch.
The HIGH, MID, and LOW values must be set so that LOW
< MID < HIGH.
This sets gain values for the positions of the GAIN switch.
The HIGH, MID, and LOW values must be set so that LOW
< MID < HIGH.
HIGH
Sets the H position.
Sets the H position.
3 dB, 6 dB, 9 dB, 12 dB, 18
dB (normal value), 18 dB +
DPR, 24 dB, 24 dB + DPR,
HYPER GAIN
dB (normal value), 18 dB +
DPR, 24 dB, 24 dB + DPR,
HYPER GAIN
MID
Sets the M position.
Sets the M position.
0 dB, 3 dB, 6 dB, 9 dB
(normal value), 12 dB, 18
dB, 18 dB + DPR, 24 dB, 24
dB + DPR
(normal value), 12 dB, 18
dB, 18 dB + DPR, 24 dB, 24
dB + DPR
LOW
Sets the L position.
Sets the L position.
–3 dB, 0 dB (normal
value), 3 dB, 6 dB, 9 dB, 12
dB, 18 dB, 18 dB + DPR, 24
dB
value), 3 dB, 6 dB, 9 dB, 12
dB, 18 dB, 18 dB + DPR, 24
dB
DL
Sets DynaLatitude function
ON/OFF. This setting is
valid only when the
OUTPUT/DL/DCC+ switch
has been set to DL.
Sets DynaLatitude function
ON/OFF. This setting is
valid only when the
OUTPUT/DL/DCC+ switch
has been set to DL.
ON (normal value), OFF
When set to ON, the amount
of DynaLatitude effects is
set in basic menu page 2
When set to ON, the amount
of DynaLatitude effects is
set in basic menu page 2
(see page 79).
Advanced menu page 2
PAGE2 (NEXTm$ PREVm4)
GAIN
m HIGH: 18dB
MID : 9dB
LOW : OdB
DL : ON
EXIT MENU (YESmPUSH)
Item
AWB MEM
Selects whether or not to
make the FILTER knob
settings (1 to 4) correspond
to separate white balance
adjustment values stored in
memory.
Selects whether or not to
make the FILTER knob
settings (1 to 4) correspond
to separate white balance
adjustment values stored in
memory.
2 (normal value): No
correspondence with FILTER
knob settings. Only two
adjustment values (A and B)
are stored in memory.
2
correspondence with FILTER
knob settings. Only two
adjustment values (A and B)
are stored in memory.
2
×
4FL: Correspondence
with FILTER knob settings.
Each of the four knob
settings can be used to set A
and B adjustment values, for
a total of eight settings.
Each of the four knob
settings can be used to set A
and B adjustment values, for
a total of eight settings.
TONE
Selects whether or not to
output a 1-kHz audio signal
with the color bars when the
OUTPUT/DL/DCC+ has
been set to BARS.
Selects whether or not to
output a 1-kHz audio signal
with the color bars when the
OUTPUT/DL/DCC+ has
been set to BARS.
ON (normal value): Output
audio signal.
OFF: Do not output audio
signal.
audio signal.
OFF: Do not output audio
signal.
BARS
Selects normal width or
narrower width for color
bars.
Selects normal width or
narrower width for color
bars.
SMPTE (normal value for
DSR-300): Normal width
EBU75 (normal value for
DSR-300P): EBU 75%
EBU100 (for DSR-300P):
EBU 100%
SPLIT (for DSR-300P): Not
for normal operation
SNG: Narrower than normal
(used for satellite
communications, etc.)
DSR-300): Normal width
EBU75 (normal value for
DSR-300P): EBU 75%
EBU100 (for DSR-300P):
EBU 100%
SPLIT (for DSR-300P): Not
for normal operation
SNG: Narrower than normal
(used for satellite
communications, etc.)
REMOTE1
Sets a function for position 1
of the RM-LG1 connected to
the REMOTE connector 1.
Sets a function for position 1
of the RM-LG1 connected to
the REMOTE connector 1.
REC (normal value):
Specifies recording start/stop
MARK: Specifies a Mark IN/
OUT point.
CUE: Specifies a Cue point.
NG: Specifies NG/OK.
Specifies recording start/stop
MARK: Specifies a Mark IN/
OUT point.
CUE: Specifies a Cue point.
NG: Specifies NG/OK.
REMOTE2
Sets a function for position 2
of the RM-LG1 connected to
the REMOTE connector 1.
Sets a function for position 2
of the RM-LG1 connected to
the REMOTE connector 1.
9600, 38400 (normal value)
REC: Specifies recording
start/stop.
MARK (normal value):
Specifies a Mark IN/OUT
point.
CUE: Specifies a Cue point
NG: Specifies NG/OK.
start/stop.
MARK (normal value):
Specifies a Mark IN/OUT
point.
CUE: Specifies a Cue point
NG: Specifies NG/OK.
Settings
BAUD RATE
Sets a baud rate for a
computer connected to the
REMOTE connector 1 (to be
supported in future version).
Sets a baud rate for a
computer connected to the
REMOTE connector 1 (to be
supported in future version).
PRE. WHT
Selects the color
temperature preset for the
white balance adjustment.
Selects the color
temperature preset for the
white balance adjustment.
3200 (normal value):
3200 K
3000: 3000 K
3200 K
3000: 3000 K