Panasonic KX-PRW120 Benutzerhandbuch
performing this procedure, and then
change it back when finished.
change it back when finished.
3
MbN: Select your wireless router’s SSID.
a MSelectN
a MSelectN
4
Confirm the SSID and then press MOKN.
5
Enter the password required to access
the wireless network. a MOKN
R After the base unit connects to the
the wireless network. a MOKN
R After the base unit connects to the
wireless router, “Connected to” and
your wireless router’s SSID is
displayed.
your wireless router’s SSID is
displayed.
6
MOFFN
Simplified configuration (WPS,
DHCP)
DHCP)
This procedure requires a wireless router that
supports WPS. If your wireless router supports
WPS, make sure the feature is turned on, and
locate its WPS button before beginning this
procedure. The WPS button is typically
labeled “WPS” or has two curved arrows on it.
supports WPS. If your wireless router supports
WPS, make sure the feature is turned on, and
locate its WPS button before beginning this
procedure. The WPS button is typically
labeled “WPS” or has two curved arrows on it.
1
MMenuN (right soft key) #523
2
MbN: “WPS (Easy setting)” a
MSelectN
MSelectN
3
Press the WPS button on your wireless
router and then press MOKN on the
handset.
R The base unit searches for your
router and then press MOKN on the
handset.
R The base unit searches for your
wireless router and “Searching...”
is displayed.
is displayed.
R After the wireless router is found, the
base unit’s Wi-Fi settings will be
completed automatically. When the
setup is complete, “Connected to”
and your wireless router’s SSID is
displayed.
completed automatically. When the
setup is complete, “Connected to”
and your wireless router’s SSID is
displayed.
4
MOFFN
Advanced configuration (static IP
settings)
settings)
After using the procedure explained in “Typical
configuration (DHCP)”, page 42 or “Simplified
configuration (WPS, DHCP)”, page 43, use
the procedure below to set the base unit’s IP
settings manually if necessary.
configuration (DHCP)”, page 42 or “Simplified
configuration (WPS, DHCP)”, page 43, use
the procedure below to set the base unit’s IP
settings manually if necessary.
This procedure is not necessary for most
users.
users.
1
MMenuN (right soft key) #500
2
MbN: “Manual (Static)” a MSelectN
3
MbN: Select the desired item. a MSelectN
4
Enter the desired setting. a MOKN
R Press MFEN to move the cursor if
R Press MFEN to move the cursor if
necessary.
5
Set the other items as necessary.
6
MbN: “<Save>” a MSelectN a MOFFN
Smartphone Connect app
Once you have configured the base unit’s
Wi-Fi and network settings, you are ready to
download the Smartphone Connect app.
Download information is available at the web
page listed below.
Wi-Fi and network settings, you are ready to
download the Smartphone Connect app.
Download information is available at the web
page listed below.
www.panasonic.net/pcc/support/tel/air
For information about using the app, refer to
the Smartphone Connect App Guide, which is
available for download at the web page listed
above.
the Smartphone Connect App Guide, which is
available for download at the web page listed
above.
Other network features
Wi-Fi repeater mode
You can increase the signal range of your
wireless network by turning on the base unit’s
Wi-Fi repeater mode feature.
wireless network by turning on the base unit’s
Wi-Fi repeater mode feature.
1
MMenuN (right soft key) #538
2
MbN: Select the desired setting. a MSaveN
Important:
R If using Wi-Fi repeater mode, do not place
R If using Wi-Fi repeater mode, do not place
the base unit and your wireless router too
close to each other. If they are too close,
close to each other. If they are too close,
For assistance, please visit http://www.panasonic.com/help
43
Smartphone Integration
PRW120(en)_1016_ver041.pdf 43
2013/10/16 10:40:19