Sony KLV-40S200A Benutzerhandbuch
33
GB
KLV-46S200A
2-891-357-11(1)
Additional Inf
o
rmation
Problem
Cause/Remedy
Only snow and noise appear
on the screen
on the screen
• Check if the antenna is broken or bent.
• Check if the antenna has reached the end of its serviceable life (three to five
• Check if the antenna has reached the end of its serviceable life (three to five
years in normal use, one to two years at the seaside).
Picture (dotted lines or stripes)
noise
noise
• Keep the TV away from electrical noise sources such as cars, motorcycles,
or hair-dryers, etc.
• Make sure that the antenna is connected using the antenna cable (supplied).
• Keep the antenna cable away from other connecting cables.
• Do not use a 300-ohm twin lead cable as interference may occur.
• Adjust the antenna direction for the minimum interference. Contact a Sony
• Keep the antenna cable away from other connecting cables.
• Do not use a 300-ohm twin lead cable as interference may occur.
• Adjust the antenna direction for the minimum interference. Contact a Sony
dealer for advice.
Picture noise when viewing a
TV channel
TV channel
• Select “Manual Program Preset” in the “Channel Setup” menu and adjust
“AFT” to obtain better picture reception (page 27).
• Select “Noise Reduction” in the “Picture” menu to reduce the noise in the
Stripe noise during playback/
recording of a VCR
recording of a VCR
• Video head interference. Keep your VCR away from the TV.
• Leave a space of 30 cm between your VCR and the TV to avoid noise.
• Avoid installing your VCR in front of the TV or beside the TV.
• Leave a space of 30 cm between your VCR and the TV to avoid noise.
• Avoid installing your VCR in front of the TV or beside the TV.
Good picture, but noisy sound
• The TV system setting is inappropriate.
If the sound of all the channels are noisy, perform “Auto Tuning” in the
“Channel Setup” menu to preset the channel again (page 26).
If the sound of some channels is noisy, select the channel, then perform
“Manual Program Preset” in the “Channel Setup” menu, and select the
appropriate TV system (“TV System”) (page 27).
“Channel Setup” menu to preset the channel again (page 26).
If the sound of some channels is noisy, select the channel, then perform
“Manual Program Preset” in the “Channel Setup” menu, and select the
appropriate TV system (“TV System”) (page 27).
Good picture, but no sound
• The volume level is too low. Press 2 + to increase the volume level.
• The sound is muted.
• The sound is muted.
Press %, or 2 + to cancel the muting.
Some tiny black points and/or
bright points on the screen
bright points on the screen
• The picture of a display unit is composed of pixels. Tiny black points and/or
bright points (pixels) on the screen do not indicate a malfunction.
No color on programs
• Select “Reset” in the “Picture” menu to return to the factory settings
No color
• The color intensity setting is too low. Select “Color” in the “Picture” menu
to adjust the color intensity (page 18).
• Adjust the antenna direction. Contact a Sony dealer for advice.
Lines moving across the TV
screen
screen
• There is interference from external sources, e.g., heavy machineries,
broadcast station nearby. Use the fine tuning (“AFT”) function (page 27).
No color or irregular color
when viewing a signal from the
Y, P
when viewing a signal from the
Y, P
B
/C
B
, P
R
/C
R
jacks of
/
1, 2
• Check the connection of the Y, P
B
/C
B
, P
R
/C
R
jacks of
/
1, 2.
• Make sure that the Y, P
B
/C
B
, P
R
/C
R
jacks of
/
1, 2 are firmly seated
in their respective jacks.
Picture flashes initially when
changing to HDMI mode or
switching on the TV with HDMI
mode
changing to HDMI mode or
switching on the TV with HDMI
mode
• It might due to authentication process between HDMI equipment and TV.
This does not indicate a malfunction.
Continued
010COV.book Page 33 Friday, September 8, 2006 9:24 AM