Lucent Technologies 362EC Benutzerhandbuch
PARTNER Endeavor Communications System Installation Instructions -
Using a 2-Slot Carrier
Using a 2-Slot Carrier
IMPORTANT: To add a 362EC module to a PARTNER Endeavor system, the PARTNER Endeavor processor
module must already be mounted on the wall. If it is not, refer to the
module must already be mounted on the wall. If it is not, refer to the
PARTNER Endeavor Installation Guide
for
instructions. Before starting, disconnect the power cord from the power jack in the carrier. Then follow the
instructions below.
instructions below.
A) Move the carrier’s On/Off switch to "Off,"
and unplug the power cord from the wall
outlet. B) To remove the cover, loosen the
screw on lower front of the cover. C) Place
one hand on the handle on the bottom front
of the cover, and place your other hand on
the top of the cover. Gently pull the cover up
and away from the carrier.
and unplug the power cord from the wall
outlet. B) To remove the cover, loosen the
screw on lower front of the cover. C) Place
one hand on the handle on the bottom front
of the cover, and place your other hand on
the top of the cover. Gently pull the cover up
and away from the carrier.
A) Label the lines and extension jacks.
B) Connect the line and telephone cords to
the appropriate jacks on the new module.
C) Route each cord through the hook on the
front of its module. D) Connect the free end
of each phone cord to the modular wall jacks
for system extensions. E) Connect the free
end of each telephone cord to the modular
connecting blocks for system extensions.
F) Gather the line and extension cords
hanging below the hook and twist tie or wire
wrap them. G) Place the bundle of wires in
the indentation on the bottom carrier.
B) Connect the line and telephone cords to
the appropriate jacks on the new module.
C) Route each cord through the hook on the
front of its module. D) Connect the free end
of each phone cord to the modular wall jacks
for system extensions. E) Connect the free
end of each telephone cord to the modular
connecting blocks for system extensions.
F) Gather the line and extension cords
hanging below the hook and twist tie or wire
wrap them. G) Place the bundle of wires in
the indentation on the bottom carrier.
NOTE:
Connect ETR and T/R combination
devices to the last two ports on the
PARTNER Endeavor processor or
362EC module.
devices to the last two ports on the
PARTNER Endeavor processor or
362EC module.
Line
Jacks
Extension
Jacks
Line
Jacks
Extension
Jacks
1
2
3
10
11
12
13
14
15
10
11
12
34
35
36
37
38
39
13
14
15
42
43
44
45
46
47
4
5
6
18
19
20
21
22
23
7
8
9
26
27
28
29
30
31
P F T
P F T
362EC
Module
Module
362EC
Module
Module
362EC
Module
Module
362EC
Module
Module
ECS
Proc.
Proc.
COMBO
COMBO
COMBO
COMBO
COMBO
MUSIC
ON
HOLD
ON
HOLD
Before installing any modules, make sure the
clear, plastic protector has been removed
from the connector area on the rear of each
module. To remove the protector, grasp the
tabs on the ends of the protector and lift.
clear, plastic protector has been removed
from the connector area on the rear of each
module. To remove the protector, grasp the
tabs on the ends of the protector and lift.
A) Plug the power cord into a properly
grounded three-prong wall outlet not
controlled by a switch. B) Power up the
control unit by moving the On/Off switch to
the "On" position.
grounded three-prong wall outlet not
controlled by a switch. B) Power up the
control unit by moving the On/Off switch to
the "On" position.
COMBO
COMBO
COMBO
COMBO
COMBO
COMBO
COMBO
COMBO
COMBO
COMBO
E
X
T
E
N
S
I
O
N
S
4
5
6
18
19
20
21
22
23
24
25
7
8
9
26
27
28
29
30
31
32
33
1
2
3
10
11
12
13
14
15
16
17
10
11
12
13
14
15
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
A) Verify that the PARTNER Endeavor
processor module is in the center slot of the
carrier. In the other slots, from left to right,
install the 362EC modules. B) Align the
module carefully in the appropriate slot, and
push slowly but firmly in the center of the
module until the connectors on the module
lock into place.
processor module is in the center slot of the
carrier. In the other slots, from left to right,
install the 362EC modules. B) Align the
module carefully in the appropriate slot, and
push slowly but firmly in the center of the
module until the connectors on the module
lock into place.
!
CAUTION:
Caution: Do not force the module. If the
module does not insert easily, remove it,
clear any obstruction, and reinsert it
module does not insert easily, remove it,
clear any obstruction, and reinsert it
Check the green lights on the fronts of the
modules. If a single light is out, power down
the carrier, then power up the carrier. If
multiple lights are out, power down the
carrier, reseat both modules, then power up
the carrier. If the lights are still out, in the
Continental U.S., call the hotline at
1-800-721-7071. Outside the Continental
U.S., contact your Lucent Technologies
Representative or local Authorized Dealer
modules. If a single light is out, power down
the carrier, then power up the carrier. If
multiple lights are out, power down the
carrier, reseat both modules, then power up
the carrier. If the lights are still out, in the
Continental U.S., call the hotline at
1-800-721-7071. Outside the Continental
U.S., contact your Lucent Technologies
Representative or local Authorized Dealer
.
A) To replace the carrier’s cover grasp it by
its upper edges and hold it squarely over the
carrier. B) Place the cover over the modules
and make sure it fits firmly in place. If it does
not fit, make sure all modules are seated
properly. C) Tighten the screw on the lower
front of the cover.
its upper edges and hold it squarely over the
carrier. B) Place the cover over the modules
and make sure it fits firmly in place. If it does
not fit, make sure all modules are seated
properly. C) Tighten the screw on the lower
front of the cover.
COMBO
COMBO
COMBO
COMBO
COMBO
COMBO
362EC
Processor
Module
Module
1 2 3
4 5 6
7